Typical ELMy H-mode discharges have been achieved on the HL-2A tokamak with combined auxiliary heating of NBI and ECRH. The minimum power required is about 1.1 MW at a density of 1.6 × 10 19 m −3 and increases with a decrease in density, almost independent of the launching order of the ECRH and NBI heating. The energy loss by each edge localized mode (ELM) burst is estimated to be lower than 3% of the total stored energy. At a frequency of typically 400 Hz, the energy confinement time is only marginally reduced by the ELMs. The supersonic molecular beam injection fuelling is found to be beneficial for triggering an L-H transition due to less induced recycling and higher fuelling efficiency. The dwell time of the L-H transition is 20-200 ms, and tends to decrease as the power increases. The delay time of the H-L transition is 10-30 ms for most discharges and is comparable to the energy confinement time. The ELMs with a period of 1-3 ms are sustained for more than ten times the energy confinement time with enhanced confinement factor H 89 > 1.5, which tends to decrease with the total heating power. The confinement time in the H-mode discharges increases with plasma current approximately linearly.

A new method of gas fuelling, pulsed supersonic molecular beam injection (SMBI), has been successfully developed and used in the HL-1M tokamak. SMBI is an attempt to enhance the penetration depth and the fuelling efficiency, as well as to reduce both the injected particle-wall surface interaction and the impurity content in the plasma. SMBI can be considered a significant improvement over conventional gas puffing. With a penetration depth of hydrogen particles greater than 15 cm, the rate of increase of electron density, dn̄e/dt, was up to 7.2 × 1020m-3 s-1 without disruption, and the highest plasma density was n̄e = 8.2 × 1019 m-3. The density profile peaking factor Qn reached a maximum value of more than 1.67 after SMBI. The energy confinement time τE measured by diamagnetism is 10-30% longer than that with gas puffing with the other discharge conditions kept the same. SMBI has recently been improved to enhance the flux of the beam and to allow a survey of the cluster effect within the beam. A series of new phenomena show the interaction of the beam (including clusters) with the toroidal plasma, which indicates that hydrogen clusters may be produced in the beam according to the Hagena empirical scaling law of clustering onset, Γ* = kd0.85P0/T02.29. If Γ* > 100, clusters will form. In the present experiment Γ* is about 127.

Recent experiment results from the HL-2A tokamak are presented in this paper. Supersonic molecular beam injection (SMBI) with liquid nitrogen temperature propellant is used. Low temperature SMBI can form hydrogen clusters that penetrate into the plasma more deeply and efficiently. Particle diffusion coefficient and convection velocity (D = 0.5–1.5 m2 s−1 and Vconv < 40 m s−1, respectively) are obtained at the plasma periphery using modulated SMBI. Multi-probe measurements reveal the m = 0–1, n = 0 symmetries of directly measured low frequency (7–9 kHz) electric potential and field are simultaneously observed for the first time. Impurity transport is determined with the laser blow-off system and transport code. A disruption predictor has been derived based on MHD activity observations and statistical analysis. Sawtooth characteristics during ECRH are investigated and coupling between m = 1 and m/n = 2/1 modes is studied. Detachment features of HL-2A divertor are numerically and experimentally studied using the code SOLPS5.0 and measured data. The long divertor legs and thin divertor throats in HL-2A pose MHD shaping problems resulting in momentum losses even at low densities and strongly enhanced main chamber losses.

ITER and to the advanced tokamak operation (e.g. the operation of future HL-2M), such as the access of H-mode, energetic particle physics, edge-localized mode (ELM) mitigation/suppression and disruption mitigation. Since the 2016 Fusion Energy Conference, the HL-2A team has focused on the investigations on the following areas: (i) pedestal dynamics and L-H transition, (ii) techniques of ELM control, (iii) the turbulence and transport, (iv) energetic particle physics. The HL-2A results demonstrated that the increase of mean E × B shear flow plays a key role in triggering L-I and I-H transitions. While the change of E × B flow is mainly induced by the ion pressure gradient. Both mitigation and suppression of ELMs were realized by laser blow-off (LBO) seeded impurity (Al, F e, W). The 30% N e mixture supersonic molecular beam injection (SMBI) seeding also robustly induced ELM mitigation. The ELMs were mitigated by low-hybrid current drive (LHCD). The stabilization of m/n=1/1 ion fishbone activities by electron cyclotron resonance heating (ECRH) was found on the HL-2A. A new m/n=2/1 ion fishbone activity was observed recently, and the modelling indicated that passing fast ions dominantly contribute to the driving of 2/1 fishbone. The non-linear coupling between toroidal Alfven eigenmode (TAE) and tearing mode (TM) leads to the generation of a high frequency mode with the toroidal mode number n=0. The turbulence is modulated by tearing mode when the island width exceeds a threshold and the modulation is localized merely in the inner area of the islands. Meanwhile, turbulence radially spreading takes place across the island region.

A method of the particle transport study using supersonic molecular beam injection (SMBI) and microwave reflectometry is reported in this paper. Experimental results confirm that pulsed SMBI is a good perturbation source with deeper penetration and better localization than the standard gas puffing. The local density modulation is induced using the pulsed SMBI and the perturbation density is measured by the microwave reflectometry. Using Fourier transform analysis for the local density perturbation, radial profiles of the amplitude and phase of the density modulation can be obtained. The experimental results in HL-2A show that the particle injected by SMBI is located at about r/a=0.65–0.75. The position of the main particle source can be determined through three aspects: the minimum of the phase of the first harmonic of the Fourier transform of the modulated density measured by microwave reflectometry; the Ha intensity profile and the local density increase ratio. The maximum of the amplitude of the first harmonic shifts often inward relative to the particle source location, which indicates clearly there is an inward particle pinch in this area. Good agreement has been found between the experimental results and the simulation using analytical transport model. The particle diffusivity D and the particle convection velocity V have been obtained by doing this simulation. The sensitivity in the transport coefficients of the amplitude and the phase of the density modulation has been discussed.