Requirements for mechanical properties of steels are constantly increasing, and the combination of quenching and tempering is the method generally chosen for achieving high strength in medium carbon steels. This study examines the influence of various silicon contents from 1.06 to 2.49 wt% and the addition of copper (1.47 wt%) on the behavior of 1.7102 steel starting with the as-quenched state and ending with the tempered condition at the temperature of 500 °C. The microstructure was characterized by SEM and TEM, the phase composition and dislocation density were studied by XRD analysis, and mechanical properties were assessed by tensile and hardness testing, whereas tempered martensite embrittlement was assessed using Charpy impact test and the activation energy of carbide precipitation was determined by dilatometry. The benefit of copper consists in the improvement of reduction of area by tempering between 150 and 300 °C. The increase in strength due to copper precipitation occurs upon tempering at 500 °C, where strength is generally low due to a drop in dislocation density and changes in microstructure. The increasing content of silicon raises strength and dislocation density in steels, but the plastic properties of steel are limited. It was found that the silicon content of 1.5 wt% is optimum for the materials under study.
Understanding the tempering behavior of medium carbon steels is mandatory if their mechanical properties are to be improved. For an optimal technology to be developed for this purpose, a substantial experimental basis is needed to extract quantitative information on the microstructure of the tempered material. This paper reports on the characterization of microstructural changes induced by tempering in medium-carbon steels alloyed with Si, Cr, Cu, and Mn using state-of-the-art experimental techniques. Complementarities among these techniques are highlighted. The evolution of transition carbides, cementite, and copper precipitates is described using data from X-ray diffraction, small and ultra-small angle neutron diffraction, transmission electron microscopy, and dilatometry observation. The effects of silicon, chromium, and copper on the mechanism of carbide and copper precipitation are discussed. The considerable changes found in the size and volume of copper precipitates correlate well with the difference in the yield stress between tempered steels with and without copper.
The 54SiCr6 steel belongs to spring steels which excel high strength and at the same time reaches high values of reduction of area and sufficient value of elongation. Nowadays, new methods are searched and examined how to get better properties from materials, higher strength and toughness, longer fatigue resistance or better corrosion properties. In the case of silicon-chromium spring steels, innovative heat treatments are investigated such as quenching and partitioning which enables to achieve higher ductility of steel due to higher content of retained austenite. The way of modification of the chemical composition of the 54SiCr6 steel was chosen in combination with conventional heat treatment composed of quenching and tempering to get better properties. The materials with increased content of copper to 1.5 wt. % and silicon to 2.5 wt. % were prepared. The influence of alloying elements on microstructure and mechanical properties was followed up to the tempering temperature of 400 °C.
Material research of the spring steels tries to meet requirements of the industry, which are mainly higher yield and tensile strength. Steel 51CrV4 is widely used for spring production. Optimization of its properties lies in tensile and yield strength enhancement without decrease in ductility in quenched and tempered state. This can be accomplished by structural refinement. One possible way to refine final quenched and tempered structure is refinement of the soft annealed structure before quenching. The article is devoted to accelerated carbide spheroidisation and refinement (ASR) and subsequent hardening of the 51CrV4 spring steel. Samples with different carbide size were prepared by conventional soft annealing in atmosphere furnace and ASR process by induction heating. Influence of the structural refinement on the properties of quenched and tempered state was studied.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.