PURPOSE The aim of this study was to investigate shade changes in fully- and pre-crystalized CAD-CAM lithium disilicate crowns after the required and additional firing processes. MATERIALS AND METHODS One hundred and five crowns of shade A1 with high translucency were milled out of CAD-CAM lithium disilicate blocks and categorized as follows (n = 15): (1) restorations fabricated from Straumann n!ce with no additional sintering process; (2) restorations fabricated from Straumann n!ce with one additional sintering process; (3) restorations fabricated from Straumann n!ce with two additional sintering processes; (4) restorations fabricated from Amber Mill with one sintering process; (5) restorations fabricated from Amber Mill with two sintering processes; (6) restorations fabricated from IPS e.max CAD with one sintering process; (7) restorations fabricated from IPS e.max CAD with two sintering processes. All restorations were evaluated with a color imaging spectrophotometer. RESULTS All restorations presented some color alteration from the original shade both after a single and after two firing processes. CONCLUSION The required and additional sintering processes for restorations fabricated with chairside CAD-CAM lithium disilicate blocks cause an alteration of the original shade selected. Shade A1 high translucency restorations tend to change to a more yellowish B1 shade after a sintering process.

To compare full and partial coverage crowns made with different CAD/CAM leucite reinforced ceramic blocks on fracture resistance and fractographic analysis. Full coverage and partial coverage crowns with finish line at 2 mm and 4 mm above the gingiva for molars made with IPS Empress CAD and Rosetta BM. After fatigue process, the fracture test and fractographic analysis were conducted. Although the fracture resistance of IPS Empress crowns did not show any statistical differences regardless of the design, both the partial coverage crowns fabricated using Rosetta BM showed significantly higher load at break and peak load than the full coverage crown. The crowns made with IPS Empress showed significantly higher fracture resistance than that made with Rosetta BM, regardless of the restorative design. The fracture resistance and fractographic analysis of CAD/CAM leucite reinforced full and partial coverage crowns were influenced by the restorative design of and material type.

PurposeThe available independent data on the translucency of novel pre and fully sintered chairside computer‐aided design and computer‐aided manufacturing (CAD–CAM) lithium disilicate are limited. This comparative in vitro study evaluated the translucency degree of pre and fully sintered chairside CAD–CAM lithium disilicate crowns after optional, required, and additional firing processes.Materials and methodsOne hundred and five maxillary left central incisor crowns manufactured by three different CAD–CAM lithium disilicate brands shade A1 were assigned into seven groups as follows (n = 15): (1) Straumann n!ce without sintering; (2) Straumann n!ce with one additional sintering process; (3) Straumann n!ce with two additional sintering processes; (4) Amber Mill with one sintering process; (5) Amber Mill with two sintering processes; (6) IPS e.max CAD with one sintering process; and (7) IPS e.max CAD with two sintering processes. The translucency of all crowns was evaluated with a color imaging spectrophotometer. All statistical analyses were performed using statistical software. A standard level of significance was set at α < 0.05.ResultsAll the milled crowns presented different degrees of translucency, and additional sintering processes altered it. IPS e.max CAD with two (4.33 ± 0.26) and one (4.01 ± 0.15) sintering processes displayed the highest translucency, whereas Straumann n!ce with no sintering process provided the lowest value (2.82 ± 0.16).ConclusionsThe translucency of chairside lithium disilicate single‐unit full‐coverage restorations manufactured with subtractive technology was significantly influenced by the brand and the number of sintering processes. The traditional presintered IPS e.max CAD and the fully crystallized glass–ceramic Straumann n!ce considerably increased the translucency after one additional firing process, whereas Amber Mill decreased its translucency.

No abstract

No abstract