Antimony (Sb) has emerged as an attractive anode material for both lithium and sodium ion batteries due to its high theoretical capacity of 660 mA h g−1. In this work, a novel peapod‐like N‐doped carbon hollow nanotube encapsulated Sb nanorod composite, the so‐called nanorod‐in‐nanotube structured Sb@N‐C, via a bottom‐up confinement approach is designed and fabricated. The N‐doped‐carbon coating and thermal‐reduction process is monitored by in situ high‐temperature X‐ray diffraction characterization. Due to its advanced structural merits, such as sufficient N‐doping, 1D conductive carbon coating, and substantial inner void space, the Sb@N‐C demonstrates superior lithium/sodium storage performance. For lithium storage, the Sb@N‐C exhibits a high reversible capacity (650.8 mA h g−1 at 0.2 A g−1), excellent long‐term cycling stability (a capacity decay of only 0.022% per cycle for 3000 cycles at 2 A g−1), and ultrahigh rate capability (343.3 mA h g−1 at 20 A g−1). For sodium storage, the Sb@N‐C nanocomposite displays the best long‐term cycle performance among the reported Sb‐based anode materials (a capacity of 345.6 mA h g−1 after 3000 cycles at 2 A g−1) and an impressive rate capability of up to 10 A g−1. The results demonstrate that the Sb@N‐C nanocomposite is a promising anode material for high‐performance lithium/sodium storage.

Rechargeable magnesium batteries are identified as a promising next‐generation energy storage system, but their development is hindered by the anode−electrolyte−cathode incompatibilities and passivation of magnesium metal anode. To avoid or alleviate these problems, the exploitation of alternative anode materials is a promising choice. Herein, we present titanium pyrophosphate (TiP2O7) as anode materials for magnesium‐ion batteries (MIBs) and investigate the effect of the crystal phase on its magnesium storage performance. Compared with the metastable layered TiP2O7, the thermodynamically stable cubic TiP2O7 displays a better rate capability of 72 mAh g−1 at 5000 mA g−1. Moreover, cubic TiP2O7 exhibits excellent cycling stability with the capacity of 60 mAh g−1 after 5000 cycles at 1000 mA g−1, which are better than previously reported Ti‐based anode materials for MIBs. In situ X‐ray diffraction technology confirms the single‐phase magnesium‐ion intercalation/deintercalation reaction mechanism of cubic TiP2O7 with a low volume change of 3.2%. In addition, the density functional theory calculation results demonstrate that three‐dimensional magnesium‐ion diffusion can be allowed in cubic TiP2O7 with a low migration energy barrier of 0.62 eV. Our work demonstrates the promise of TiP2O7 as high‐rate and long‐life anode materials for MIBs and may pave the way for further development of MIBs.

There has been a substantial growth in the application of mass spectrometry (MS) methods for the analysis of inorganic materials, due to the inherent sensitivity of mass spectrometry ionization to the specific composition and structure of the analyzed materials. To date, few mass spectrometry studies have focused on metal-chalcogenide materials, an important class of semiconductor materials at the nanoscale, that exhibit interesting optical and electronic properties as a function of size. In this study, we report the application of a correlated electrospray mass spectrometry (ESMS) study between negative-ion and positive-ion mode under low-cone voltage to probe size, composition, and stability of metal-chalcogenide materials at the <1 nm scale. This correlation approach provides insight into the ionization behavior and thermodynamic stability of clusters in the <1.0 nm size domain of the form [Zn4(SPh)10][Me4N]2, [Cd4(SPh)10][Me4N]2, [E4Zn10(SPh)16][Me4N]4, [E4Cd10(SPh)16][Me4N]4 (E = S, Se). It is demonstrated that application of low-cone voltage ESMS can be a useful technique for the rapid analysis of intact solid state nanomaterials when both negative and positive ionic modes are analyzed, with a potential for extrapolation to other classes of nanoscale materials.

Water-dispersible CdS quantum dots (QDs) emitting from 510 to 650 nm were synthesized in a simple one-pot noninjection hydrothermal route using cadmium chloride, thiourea, and 3-mercaptopropionic acid (MPA) as starting materials. All these chemicals were loaded at room temperature in a Teflon sealed tube and the reaction mixture heated at 100 °C. The effects of CdCl(2)/thiourea/MPA feed molar ratios, pH, and concentrations of precursors affecting the growth of the CdS QDs, was monitored via the temporal evolution of the optical properties of the CdS nanocrystals. High concentration of precursors and high MPA/Cd feed molar ratios were found to lead to an increase in the diameter of the resulting CdS nanocrystals and of the trap state emission of the dots. The combination of moderate pH value, low concentration of precursors and slow growth rate plays the crucial role in the good optical properties of the obtained CdS nanocrystals. The highest photoluminescence achieved for CdS@MPA QDs of average size 3.5 nm was 20%. As prepared colloids show rather narrow particle size distribution, although all reactants were mixed at room temperature. CdS@MPA QDs were characterized by UV-vis and photoluminescence spectroscopy, powder X-ray diffraction, transmission electron microscopy, energy-dispersive X-ray spectrometry and MALDI TOF mass spectrometry. This noninjection one-pot approach features easy handling and large-scale production with excellent synthetic reproducibility. Surface passivation of CdS@MPA cores by a wider bandgap material, ZnS, led to enhanced luminescence intensity. CdS@MPA and CdS/ZnS@MPA QDs exhibit high photochemical stability and hold a good potential to be applied in optoelectronic devices and biological applications.

No abstract