There is an increasing demand for lightweight composites reinforced with carbon fibers (CFs). Due to its high availability and carbon content, kraft lignin has gained attention as a potential low-cost CF precursor. CFs with promising properties can be made from flexible dry-jet wet spun precursor fibers (PFs) from blends (70:30) of softwood kraft lignin and fully bleached softwood kraft pulp. This study focused on reducing the stabilization time, which is critical in CF manufacturing. The impact of stabilization conditions on chemical structure, yield, and mechanical properties was investigated. It was possible to reduce the oxidative stabilization time of the PFs from about 16 h to less than 2 h, or even omitting the stabilization step, without fusion of fibers. The main reactions involved in the stabilization stage were dehydration and oxidation. The results suggest that the isothermal stabilization at 250 °C override the importance of having a slow heating rate. For CFs with a commercial diameter, stabilization of less than 2 h rendered in tensile modulus 76 GPa and tensile strength 1070 MPa. Impregnation with ammonium dihydrogen phosphate significantly increased the CF yield, from 31−38 to 46−50 wt %, but at the expense of the mechanical properties.

To meet the demand for carbon-fibre-reinforced composites in lightweight applications, cost-efficient processing and new raw materials are sought for. Cellulose and kraft lignin are each interesting renewables for this purpose due to their high availability. The molecular order of cellulose is an excellent property, as is the high carbon content of lignin. By co-processing cellulose and lignin, the advantages of these macromolecules are synergistic for producing carbon fibre (CF) of commercial grade in high yields. CFs were prepared from precursor fibres (PFs) made from 70:30 blends of softwood kraft lignin (SW-KL) and cellulose by dry-jet wet spinning with the ionic liquid (IL) 1-ethyl-3-methylimidazolium acetate ([EMIm][OAc]) as a solvent. In focus was the impact of the molecular mass of lignin and the type of cellulose source on the CF yield and properties, while membrane-filtrated kraft lignin and cellulose from dissolving kraft pulp and fully bleached paper-grade SW-KP (kraft pulp) served as sources. Under the investigated conditions, the yield increased from around 22% for CF from neat cellulose to about 40% in the presence of lignin, irrespective of the type of SW-KL. The yield increment was also higher relative to the theoretical one for CF made from blends (69%) compared to those made from neat celluloses (48–51%). No difference in the mechanical properties of the produced CF was observed.

In this study, the underlying mechanism for improved spinnability when mixing lignin and cellulose in solution was investigated. Co‐processing of lignin and cellulose has previously been identified as a potential route for production of inexpensive and bio‐based carbon fibers. The molecular order of cellulose contributes to the strength of the fibers and the high carbon content of lignin improves the yield during conversion to carbon fibers. The current work presents an additional benefit of combining lignin and cellulose; solutions that contain both lignin and cellulose could be air‐gap spun at substantially higher draw ratios than pure cellulose solutions, that is, lignin improved the spinnability. Fibers were spun from solutions containing different ratios of lignin, from 0 to 70 wt%, and the critical draw ratio was determined at various temperatures of solution. The observations were followed by characterization of the solutions with shear and elongational viscosity and surface tension, but none of these methods could explain the beneficial effect of lignin on the spinnability. However, by measuring the take‐up force it was found that lignin seems to stabilize against diameter fluctuations during spinning, and plausible explanations are discussed.

Chemical recycling of textiles holds the potential to yield materials of equal quality and value as products from virgin feedstock. Selective depolymerization of textile polyester (PET) from regenerated cellulose/PET blends, by means of alkaline hydrolysis, renders the monomers of PET while cellulose remains in fiber form. Here, we present the mechanism and reactivity of textile PET during alkaline hydrolysis. Part I of this article series focuses on the cellulose part and a possible industrialization of such a process. The kinetics and reaction mechanism for alkaline hydrolysis of polyester packaging materials or virgin bulk polyester are well described in the scientific literature; however, information on depolymerization of PET from textiles is sparse. We find that the reaction rate of hydrolysis is not affected by disintegrating the fabric to increase its surface area. We ascribe this to the yarn structure, where texturing and a low density assures a high accessibility even without disintegration. The reaction, similar to bulk polyester, is shown to be surface specific and proceeds via endwise peeling. Finally, we show that the reaction product terephthalic acid is pure and obtained in high yields.