Bring home now the book enPDFd rf superconductivity for accelerators to be your sources when going to read. It can be your new collection to not only display in your racks but also be the one that can help you fining the best sources. As in common, book is the window to get in the world and you can open the world easily. These wise words are really familiar with you, isn't it?

The photoinjector test facility at DESY, Zeuthen site (PITZ), was built to develop and optimize photoelectron sources for superconducting linacs for high-brilliance, short-wavelength free-electron laser (FEL) applications like the free-electron laser in Hamburg (FLASH) and the European x-ray free-electron laser (XFEL). In this paper, the detailed characterization of two laser-driven rf guns with different operating conditions is described. One experimental optimization of the beam parameters was performed at an accelerating gradient of about 43 MV=m at the photocathode and the other at about 60 MV=m. In both cases, electron beams with very high phase-space density have been demonstrated at a bunch charge of 1 nC and are compared with corresponding simulations. The rf gun optimized for the lower gradient has surpassed all the FLASH requirements on beam quality and rf parameters (gradient, rf pulse length, repetition rate) and serves as a spare gun for this facility. The rf gun studied with increased accelerating gradient at the cathode produced beams with even higher brightness, yielding the first demonstration of the beam quality required for driving the European XFEL: The geometric mean of the normalized projected rms emittance in the two transverse directions was measured to be 1:26 ` 0:13 mm mrad for a 1-nC electron bunch. When a 10% charge cut is applied excluding electrons from those phase-space regions where the measured phase-space density is below a certain level and which are not expected to contribute to the lasing process, the normalized projected rms emittance is about 0.9 mm mrad

No abstract

Many next-generation, high-gradient accelerator applications, from energy-recovery linacs to accelerator-driven systems (ADS) rely on continuous wave (CW) operation for which superconducting radio-frequency (SRF) systems are the enabling technology. However, while SRF cavities dissipate little power, they must be cooled by liquid helium and for many CW accelerators the complexity as well as the investment and operating costs of the cryoplant can prove to be prohibitive. We investigated ways to reduce the dynamic losses by improving the residual resistance (R res) of niobium cavities. Both the material treatment and the magnetic shielding are known to have an impact. In addition, we found that R res can be reduced significantly when the cool-down conditions during the superconducting phase transition of the niobium are optimized. We believe that not only do the cool-down conditions impact the level to which external magnetic flux is trapped in the cavity but also that thermoelectric currents are generated which in turn create additional flux that can be trapped. Therefore, we investigated the generation of flux and the dynamics of flux trapping and release in a simple model niobium-titanium system that mimics an SRF cavity in its helium tank. We indeed found that thermal gradients along the system during the superconducting transition can generate a thermoelectric current and magnetic flux, which subsequently can be trapped. These effects may explain the observed variation of the cavity's R res with cool-down conditions.

Trapped magnetic flux is known to be one cause of residual losses in bulk niobium superconducting radio frequency cavities. In the Meissner state an ambient magnetic field should be expelled from the material. Disturbances such as lattice defects or impurities have the ability to inhibit the expulsion of an external field during the superconducting transition so that the field is trapped. We have investigated the effect the treatment history of bulk niobium has on the trapped flux and which treatment leads to minimal flux trapping. For that purpose, we measured the fraction of trapped magnetic flux in niobium samples representing cavities with different typical treatment histories. The differences between single crystal and polycrystalline material as well as the influence of spatial temperature gradients and different cooling rates were investigated. In addition, the progression of the release of a trapped field during warm-up was studied. We found that heat treatment reduces trapped flux considerably and that single crystal samples trap less flux than polycrystalline niobium. As a consequence, the single crystal sample with 1200 C baking trapped the smallest amount of field which is about 42%. Moreover, the release of the trapped field during warm-up was observed to progress over a broad temperature range for the baked single crystal samples.