High charge-separation efficiency combined with the reduced fabrication costs associated with solution processing and the potential for implementation on flexible substrates make 'plastic' solar cells a compelling option for tomorrow's photovoltaics. Attempts to control the donor/acceptor morphology in bulk heterojunction materials as required for achieving high power-conversion efficiency have, however, met with limited success. By incorporating a few volume per cent of alkanedithiols in the solution used to spin-cast films comprising a low-bandgap polymer and a fullerene derivative, the power-conversion efficiency of photovoltaic cells (air-mass 1.5 global conditions) is increased from 2.8% to 5.5% through altering the bulk heterojunction morphology. This discovery can potentially enable morphological control in bulk heterojunction materials where thermal annealing is either undesirable or ineffective.

Tandem solar cells, in which two solar cells with different absorption characteristics are linked to use a wider range of the solar spectrum, were fabricated with each layer processed from solution with the use of bulk heterojunction materials comprising semiconducting polymers and fullerene derivatives. A transparent titanium oxide (TiO(x)) layer separates and connects the front cell and the back cell. The TiO(x) layer serves as an electron transport and collecting layer for the first cell and as a stable foundation that enables the fabrication of the second cell to complete the tandem cell architecture. We use an inverted structure with the low band-gap polymer-fullerene composite as the charge-separating layer in the front cell and the high band-gap polymer composite as that in the back cell. Power-conversion efficiencies of more than 6% were achieved at illuminations of 200 milliwatts per square centimeter.

Metal halide perovskites of the general formula ABX 3 -where A is a monovalent cation such as caesium, methylammonium or formamidinium; B is divalent lead, tin or germanium; and X is a halide anion-have shown great potential as light harvesters for thin-film photovoltaics [1][2][3][4][5] . Among a large number of compositions investigated, the cubic α-phase of formamidinium lead triiodide (FAPbI 3 ) has emerged as the most promising semiconductor for highly efficient and stable perovskite solar cells [6][7][8][9] , and maximizing the performance of this material in such devices is of vital importance for the perovskite research community. Here we introduce an anion engineering concept that uses the pseudo-halide anion formate (HCOO − ) to suppress anion-vacancy defects that are present at grain boundaries and at the surface of the perovskite films and to augment the crystallinity of the films. The resulting solar cell devices attain a power conversion efficiency of 25.6 per cent (certified 25.2 per cent), have long-term operational stability (450 hours) and show intense electroluminescence with external quantum efficiencies of more than 10 per cent. Our findings provide a direct route to eliminate the most abundant and deleterious lattice defects present in metal halide perovskites, providing a facile access to solution-processable films with improved optoelectronic performance.Perovskite solar cells (PSCs) have attracted much attention since their first demonstration in 2009 [1][2][3][4][5] . The rapid expansion of research into PSCs has been driven by their low-cost solution processing and attractive optoelectronic properties, including a tunable bandgap 6 , high absorption coefficient 10 , low recombination rate 11 and high mobility of charge carriers 12 . Within a decade, the power conversion efficiency (PCE) of single-junction PSCs progressed from 3% to a certified value of 25.5% 13 , the highest value obtained for thin-film photovoltaics. Moreover, through the use of additive and interface engineering strategies, the long-term operational stability of PSCs now exceeds 1,000 hours in full sunlight 14,15 . PSCs therefore show great promise for deployment as the next generation of photovoltaics.Compositional engineering plays a key part in achieving highly efficient and stable PSCs. In particular, mixtures of methylammonium lead triiodide (MAPbI 3 ) with formamidinium lead triiodide (FAPbI 3 ) have been extensively studied 5,7 . Compared to MAPbI 3 , FAPbI 3 is thermally more stable and has a bandgap closer to the Shockley-Queisser limit 6 , rendering FAPbI 3 the most attractive perovskite layer for single-junction PSCs.Unfortunately, thin FAPbI 3 films undergo a phase transition from the black α-phase to a photoinactive yellow δ-phase below a temperature of 150 °C. Previous approaches to overcome this problem have included mixing FAPbI 3 with a combination of methylammonium (MA + ), caesium (Cs + ) and bromide (Br − ) ions; however, this comes at the cost of blue-shifted absorbance and phase segregation under...

Two criteria for processing additives introduced to control the morphology of bulk heterojunction (BHJ) materials for use in solar cells have been identified: (i) selective (differential) solubility of the fullerene component and (ii) higher boiling point than the host solvent. Using these criteria, we have investigated the class of 1,8-di(R)octanes with various functional groups (R) as processing additives for BHJ solar cells. Control of the BHJ morphology by selective solubility of the fullerene component is demonstrated using these high boiling point processing additives. The best results are obtained with R ) Iodine (I). Using 1,8-diiodooctane as the processing additive, the efficiency of the BHJ solar cells was improved from 3.4% (for the reference device) to 5.1%.