Abstract. For almost 10 years the KTB superdeep drilling project has offered an excellent field laboratory for adapting seismic techniques to crystalline environments and for testing new ideas for interpreting seismic reflections in terms of lithological or textural properties of metamorphic rock units. The seismic investigations culminated in a threedimensional (3-D) reflection survey on a 19 x 19 km area with the drill site at its center. Interpretation of these data resulted in a detailed, structural model of the German Continental Deep Drilling Program (KTB) location with dominant, steep faults in the upper crust. The 3-D reflection survey was part of a suite of seismic experiments, ranging from wide-angle reflection and refraction profiles to standard vertical seismic profiles (VSP) and more sophisticated surface-to-borehole observations. It was predicted that the drill bit would meet the most prominent, steeply dipping, crustal reflector at a depth of about 6500-7000 m, and indeed, the borehole penetrated a major fault zone in the depth interval between 6850 and 7300 m. This reflector offered the rare opportunity to relate logging results, reflective properties, and geology to observed and modeled data. PostVariscan thrusting caused cataclastic deformation, with partial, strong alterations within a steeply dipping reverse fault zone. This process generated impedance contrasts within the fault zone on a lateral scale large enough to cause seismic reflections. This was confirmed by borehole measurements along the whole 9.1 km deep KTB profile. The strongest, reflected signals originated from fluid-filled fractures and cataclastic fracture zones rather than from lithological boundaries (i.e., first-order discontinuities between different rock types) or from texture-and/or foliation-induced anisotropy. During the interpretation of seismic data at KTB several lessons were learned: Conventional processing of twodimensional (2-D) reflection data from a presite survey showed predominantly subhorizontal layering in the upper crust with reflectivity striking in the Variscan direction. Drilling, however, revealed that all rock units are steeply dipping. This confirms that surface common depth point (CDP) seismics strongly enhances subhorizontal reflectivity and may thus produce a very misleading crustal image. Although this was shown for synthetic examples earlier, the KTB provides the experimental proof of how crucial this insight can be.

[1] The lowermost section of the continental superdeep drill hole German Continental Deep Drilling Program (KTB) (south Germany) has been investigated for the first time by vertical seismic profiling (VSP). The new VSP samples the still accessible range of 6-8.5 km depth. Between 7 and 8.5 km depth, the drill hole intersects a major cataclastic fault zone which can be traced back to the Earth's surface where it forms a lineament of regional importance, the Franconian line. To determine the seismic properties of the crust in situ, in particular within and around this deep fault zone, was one of the major goals of the VSP. For the measurements a newly developed high-pressure/high-temperature borehole geophone was used that was capable of withstanding temperatures and pressures up to 260°C and 140 MPa, respectively. The velocity-depth profiles and reflection images resulting from the VSP are of high spatial resolution due to a small geophone spacing of 12.5 m and a broad seismic signal spectrum. Compared to the upper part of the borehole, we found more than 10% decrease of the P wave velocity in the deep, fractured metamorphic rock formations. P wave velocity is $5.5 km/s at 8.5 km depth compared to 6.0-6.5 km/s at more shallow levels above 7 km. In addition, seismic anisotropy was observed to increase significantly within the deep fracture zone showing more than 10% shear wave splitting and azimuthal variation of S wave polarization. In order to quantify the effect of fractures on the seismic velocity in situ we compared lithologically identical rock units at shallow and large depths: Combining seismic velocity and structural logs, we could determine the elastic tensors for three gneiss sections. The analysis of these tensors showed that we need fracture porosity in the percent range in order to explain seismic velocity and anisotropy observed within the fault zone. The opening of significant pore space around 8 km depth can only be maintained by differential tectonic stress combined with intense macroscopic fracturing. VSP reflection imaging based on PP and PS converted reflected waves showed that the major fault system at the KTB site is wider and more complex than previously known. The so-called SE1 reflection previously found in two-and three-dimensional surface seismic surveys corresponds to the top of an $1 km wide fault system. Its lower portion was not illuminated by surface seismic acquisition geometry. VSP imaging shows that the fault zone comprises two major and a number of smaller SE dipping fault planes and several conjugate fracture planes. The previously recognized upper fault plane is not associated with a strong velocity anomaly but indicates the depth below which the dramatic velocity decrease starts. Regarding the complexly faulted crustal section of the KTB site as a whole, we found that fluctuation spectra of rock composition and seismic velocity show similar patterns. We could verify that a significant amount of P wave energy is continuously converted into shear energy by forward scattering a...

No abstract

No abstract

No abstract