Molecularly Imprinted Polymers (MIPs) are synthetic receptors that are able to selectively bind their target molecule and, for this reason, they are currently employed as recognition elements in sensors. In this work, MIP nanoparticles (nanoMIPs) are produced by solid-phase synthesis for a range of templates with different sizes, including a small molecule (biotin), two peptides (one derived from the epithelial growth factor receptor and vancomycin) and a protein (trypsin). NanoMIPs are then dipcoated on the surface of thermocouples that measure the temperature inside a liquid flow cell. Binding of the template to the MIP layer on the sensitive area of the thermocouple tip blocks the heat-flow from the sensor to the liquid, thereby lowering the overall temperature measured by the thermocouple. This is subsequently correlated to the concentration of the template, enabling measurement of target molecules in the low nanomolar regime. The significant improvement in the limit of detection (a magnitude of three orders compared to previously used MIP microparticles) can be attributed to their high affinity, enhanced conductivity and increased surface-to-volume ratio. It is the first time that these nanosized recognition elements are used in combination with thermal detection, and it is the first report on MIP-based thermal sensors for determining protein levels. The developed thermal sensors have a high selectivity, fast measurement time (<5 min), and data analysis is straightforward, which makes it possible to monitor biomolecules in real-time. The set of biomolecules discussed in this manuscript show that it is possible to cover a range of template molecules regardless of their size, demonstrating the general applicability of the biosensor platform. In addition, with its high commercial potential and biocompatibility of the MIP receptor layer, this is an important step towards sensing assays for diagnostic applications that can be used in vivo.

This manuscript describes the production of Molecularly Imprinted Polymer nanoparticles (nanoMIPs) for the cardiac biomarkers heart-fatty acid binding protein (H-FABP) and ST2 by solid-phase synthesis, and their use as synthetic antibodies in a multiplexed sensing platform. Analysis by Surface Plasmon Resonance (SPR) shows that the affinity of the nanoMIPs is similar to that of commercially available antibodies. The particles are coated onto the surface of thermocouples and inserted into 3D-printed flow cells of different multiplexed designs. We demonstrate it is possible to selectively detect both cardiac biomarkers within the physiologically relevant range. Furthermore, the developed sensor platform is the first example of a multiplex format of this thermal analysis technique which enables simultaneous measurements of two different compounds with minimal cross selectivity. The format where three thermocouples are positioned in parallel exhibits the highest sensitivity, which is explained by modelling the heat flow distribution within the flow cell. This design is used in further experiments and proof-of-application of the sensor platform is provided by measuring spiked fetal bovine serum samples. Due to the high selectivity, short measurement time, and low-cost of this array format, it provides an interesting alternative to traditional immunoassays. The use of nanoMIPs enables a multi-marker strategy, which has the potential to contribute to sustainable healthcare by improving reliability of cardiac biomarker testing.

Pluronics (tri-block copolymers) have a significant role in the pharmaceutical industry and are being used to enhance the solubility and delivery of hydrophobic drugs in different marketed formulations. However, instability and unsatisfactory drug-loading capacity are the major weak spots of these pluronic micelles. The present research work is designed to solve the existing issues by the solubilization study of hydrophobic drugs in different pluronic micelles at variable temperatures. The solubilization of the hydrophobic antiepileptic drug lamotrigine (LAM) in five different pluronic micelles viz. P84, P85, F127, F108, and F68 was studied at different temperatures, 37, 47, and 57 °C, using UV–visible spectroscopy. The solubilization of LAM in pluronic micelles increased with the increase in temperature. Small-angle neutron scattering (SANS) measurements were used to observe the morphological and structural changes taking place in pluronics by increasing the temperature. The SANS results showed the morphological changes of spherical P84 micelles to prolate ellipsoidal micelles at 57 °C due to remarkable increase in the aggregation number. This morphological conversion was further confirmed by the heat transfer method (HTM) and dynamic light scattering (DLS) measurements. DLS measurements confirmed that LAM-loaded micelles showed a greater hydrodynamic diameter ( D h ) compared to unloaded micelles, assuring LAM solubilization in the pluronic micelles. The rate of controlled release of LAM from five different pluronic micelles was accessed by using different kinetic models to evaluate the in vitro release profile. This is the first report in which HTM measurements are established for the analysis of morphological changes in the thermoresponsive pluronic micelles in real time. The present work corroborates how we can control the drug-loading capacity, morphological structure of the drug carrier, as well as drug release by simply changing the temperature of pluronic micellar media.

Molecularly Imprinted Polymers (MIPs) are synthesized for the neurotransmitter noradrenaline with the optimal composition and binding conditions being determined via optical batch rebinding experiments. Next, the obtained MIP polymer particles are mixed within screen-printed inks to produce mass-producible bulk modified MIPs screen-printed electrodes (MIP-SPEs). In this contribution, the supporting surface which the MIP-SPEs are screen-printed upon are explored to deviate from conventional polyester, to polyvinylchloride, tracing paper and household-printing paper. The performance of the MIP-SPEs are measured using the Heat-Transfer Method (HTM), a straightforward and low-cost detection technique based on thermal resistance. At first, the noise on the signal is minimized by adjusting the settings of the temperature feedback loop. Second, the response of the MIP-SPEs to noradrenaline is measured and compared for the different substrate materials. Sensors printed onto paper are considered in further experiments as their response to noradrenaline is the highest and advantageous material properties, including sustainability and flexibility of the material. Subsequently, dose-response curves are determined by simultaneously measuring HTM and Thermal Wave Transport Analysis (TWTA). The latter is a new thermal detection method that relies on the use of thermal waves and has the advantage of a short measurement time (2 min). With these thermal methods, it is possible to specifically detect noradrenaline in aqueous solutions and quantify it at relevant concentrations. In summary, by combining synthetic receptors with thermal measurement techniques it is possible to develop a portable sensor platform that is capable of low-cost and straightforward detection of biomolecules. Through exploring novel SPE substrates, a system is designed that is flexible and holds potential for the use in commercial biomedical devices and complex sensor architectures.

Molecularly Imprinted Polymers (MIPs) are synthesized for the selective detection of caffeine. The polymerization process, monomer and crosslinker monomer composition are varied to determine the optimal synthesis procedure via batch rebinding experiments evaluated with optical detection. The selectivity is tested by comparing the response of caffeine to compounds with similar chemical structures (theophylline and theobromine) and dopamine, another neurotransmitter. Subsequently, the MIP polymer particles are integrated into bulk modified MIP screen-printed electrodes (MIP-modified SPEs). The sensors are used to measure caffeine content in various samples employing the Heat-Transfer Method (HTM), a low-cost and simple thermal detection method that is based on differences in thermal resistance at the solid-liquid interface. At first, the noise is minimized by adjusting the settings of temperature feedback loop. Second, the response of the MIP-modified SPE is studied at various temperatures ranging from 37 to 50 and 85 °C. The binding to MIP-modified SPEs has never been studied at elevated temperatures since most biomolecules are not stable at those temperatures.Using caffeine as proof-of-concept, it is demonstrated that at 85 °C the detection limit is significantly enhanced due to higher signal to noise ratios and enhanced diffusion of the biomolecule. Thermal wave transport analysis (TWTA) is also optimized at 85 °C producing a limit of detection of ~1 nM. Next, MIP-modified SPEs are used to measure the caffeine concentration in complex samples including caffeinated beverages, spiked tap water and waste water samples.The use of MIP-modified SPEs combined with thermal detection provides sensors that can be used for fast and low-cost detection performed on-site, which holds great potential for the determination of contaminants in environmental samples. The platform is generic and by adapting the MIP layer, we can expand to this a range of relevant targets.