The design and initial characterization of two-dimensional arrays of colloidal Au particles are reported. These surfaces are prepared by self-assembly of 12 nm diameter colloidal Au particles onto immobilized polymers having pendant functional groups with high affinity for Au (i.e., CN, SH, and NH2). The polymers are formed by condensation of functionalized alkoxysilanes onto cleaned quartz, glass, and SiC>2 surfaces. The assembly protocol is carried

The self-assembly of monodisperse gold and silver colloid particles into monolayers on polymer-coated substrates yields macroscopic surfaces that are highly active for surface-enhanced Raman scattering (SERS). Particles are bound to the substrate through multiple bonds between the colloidal metal and functional groups on the polymer such as cyanide (CN), amine (NH(2)), and thiol (SH). Surface evolution, which can be followed in real time by ultraviolet-visible spectroscopy and SERS, can be controlled to yield high reproducibility on both the nanometer and the centimeter scales. On conducting substrates, colloid monolayers are electrochemically addressable and behave like a collection of closely spaced microelectrodes. These favorable properties and the ease of monolayer construction suggest a widespread use for metal colloid-based substrates.

This paper details the kinetic aspects of covalent self-assembly of colloidal Au particles from solution onto immobilized organosilane polymers. On glass substrates, surface formation can be monitored using UV−vis spectroscopy and field emission scanning electron microscopy (FE-SEM). Correlation of these data allows the effect of nanostructure on bulk optical properties to be evaluated. At short derivatization times, particle coverage is proportional to (time)1/2. The particle sticking probability p, defined as the ratio of bound particles to the number of particles reaching the surface in a given time period, can be determined from a knowledge of the particle radius, solution concentration, temperature, and solution viscosity; for surfaces derivatized with (3-mercaptopropyl)trimethoxysilane (MPTMS), p ≈ 1. At longer derivatization times, interparticle repulsions result in a “saturation” coverage at ≈30% of a close-packed monolayer. Two approaches for modulating the rate of surface formation are described:  electrochemical potential control on organosilane-modified SnO2 electrodes and charge screening by organic adsorbates. Self-assembly of colloidal Au particles onto functionalized substrate surfaces is a reproducible phenomenon, as evidenced by UV−vis and surface enhanced Raman scattering (SERS) measurements on identically prepared substrates.

Ag-coated Au colloidal particles have been prepared by reduction of Ag+ in the presence of preformed Au colloids. The composition of the Au100-x Ag x particles was varied from x = 0 to 80. SERS spectra of pyridine, p-nitroso-N,N‘-dimethylaniline (p-NDMA), and trans-1,2-bis(4-pyridyl)ethylene (BPE) have been obtained with these colloids. At monolayer Ag coverages (x < 10), the optical spectra of Ag-coated Au particles are indistinguishable from uncoated Au particles. However, the SERS behavior of aggregated colloids with 647.1 nm excitation is extremely dependent upon the Ag:Au ratio. Very small amounts of Ag (x ≤ 5) lead to an increase in SERS intensity, but further increases lead to complete loss of signal. For p-NDMA and pyridine, these data can be explained by Ag inhibition of adsorbate-induced aggregation. The initial increase in SERS intensity results from production of smaller aggregates that exhibit a surface plasmon band in better alignment with the excitation wavelength; higher ratios of Ag eliminate aggregation and all SERS enhancement. For BPE, the same Ag-induced loss of SERS is observed, even though each of the Au100-x Ag x colloidal solutions is clearly aggregated by BPE adsorption. This finding suggests that submonolayers of Ag modulate specific chemical interactions between the Au and BPE that are responsible for SERS.

Covalent attachment of nanometer-scale colloidal Au particles to organosilane-coated substrates is a flexible and general approach to formation of macroscopic Au surfaces that have well-defined nanostructure. Variations in substrate (glass, metal, Al2O3), geometry (planar, cylindrical), functional group (−SH, −P(C6H5)2, −NH2, −CN), and particle diameter (2.5−120 nm) demonstrate that each component of these assemblies can be changed without adverse consequences. Information about particle coverage and interparticle spacing has been obtained using atomic force microscopy, field emission scanning electron microscopy, and quartz crystal microgravimetry. Bulk surface properties have been probed with UV−vis spectroscopy, cyclic voltammetry, and surface enhanced Raman scattering. Successful application of the latter two techniques indicates that these substrates may have value for Raman and electrochemical measurements. The assembly method described herein is compared with previous methods for controlling the nanoscale roughness of metal surfaces, and its potential applicability to the assembly of other colloidal materials is discussed.