It is often debated that the protection against solar-induced erythema under real conditions is dependent upon the amount of sunscreen applied. It is believed that when too little is applied a lower sun protection than indicated on the label will result. The aim of this study was to quantify this effect. In this multicenter study, the influence of three different amounts (0.5, 1.0, 2.0 mg/cm²) of three commercial sunscreen products in three reliable test centers was investigated according to the test protocol of The International Sun Protection Factor Test Method. The main result was a linear dependence of the SPF on the quantity applied. Taking into consideration the volunteer-specific variations, an exponential dependence of confidence interval of the in vivo SPF and amount applied was found. The highest amount applied (2.0 mg/cm²) was linked to the lowest confidence intervals. Thus, from the point of view of producing reliable and reproducible in vivo results under laboratory conditions, the recommendation of this multicenter study is an application quantity of 2.0 mg/cm².

The first metal‐induced syntheses of dicarboxylic acids from ethylene and the C1 building block CO2 have been achieved by use of the title compound 2, an unsaturated 16‐electron Fe0 system. By addition of ligands, the reactions can be controlled to give either the methylmalonic acids 1 or the isomeric succinic acids 3 preferentially.

In the past, several attempts have been made to develop in vitro methods for determining protection against UV radiation. To date however, there is no broadly accepted method. Various known and unknown parameters influence the transmission measurements of scattering films, such as the multifaceted compositions of sunscreens, the technical limitations of measurement devices as well as the difficulty to apply very thin films of sunscreen in a reproducible manner throughout different laboratories. In vitro data were measured in this multicenter study to compare possible methodologies and strategies for an in vitro approach to the sun protection factor (SPF). This publication will not present a final in vitro SPF test method, but it will point out which technical side effects may influence such a method. Influential factors such as the quality of spectrophotometer used, the amount of product applied, pretreatment of samples, time and temperature of equilibration, size of the measured surface, the application process or the calculation on the basis of standardized data are presented and discussed. Finally, a reduction of the standard deviations within single laboratories could be realized for in vitro SPF testing, but no improvement of the interlaboratory comparison was obtained. The development of a valid and reliable SPF in vitro test still remains a challenge, and further work is necessary to develop a satisfactory method.

The aim of the study was to develop a simple reproducible and reliable in vitro water resistance (WR) method to assess the sun care products. This paper is the result of a scientific collaboration between seven different international industrial laboratories and testing institutes. The same group has already achieved an in vitro protocol for the sun protection factor (SPF) determination [1]. The in vitro WR of sunscreens was tested by applying the same principle as in vivo, which determines the percentage of retention of sunscreen products by assessing the SPF before and after water immersion. Special care was taken to study the parameters influencing the WR and the possibility to follow the kinetics of sunscreen retention during water immersion. The influence of different water qualities has been tested, and osmosed water (1-3 microS cm(-1)) was chosen for the main ring study. Measurement was carried out after 5, 20 and 40 min of immersion. Histograms of selected products demonstrate the percentage of WR at all measuring times and centres, and the regression coefficient to the in vivo determination was shown and statistical calculations clearly demonstrate the reproducibility of the results between the different evaluation centres. The presented method is a practical, convenient and relevant tool for WR screening of sun care and skin care products. It even has the potential to be the starting point for the replacement of the in vivo method in future.

Der C1‐Baustein CO2 läßt sich unter CC‐Verknüpfung an den Fe0‐Komplex 1, L=PMe3, addieren. Der entstehende Carboxylat‐Komplex 2 ist sehr stabil und zeigt in Lösung ein dynamisches Verhalten. 2 reagiert mit FeCl3 zur linearen, doppelt ungesättigten α,ω‐Dicarbonsäure 3.magnified image