[1] Arctic regional climate is influenced by the radiative impact of aerosol black carbon (BC) both in the atmosphere and deposited on the snow and ice covered surfaces. The NIES (National Institute for Environmental Studies) global atmospheric transport model was used, with BC emissions from mid-latitude fossil fuel and biomass burning source regions, to simulate BC concentrations with 16 year period. The model-simulated BC agreed well with the BC observations, including the trends and seasonality, at three Arctic sites: Alert (Nunavut, Canada), Barrow (Alaska, USA), and Zepplin, Ny-Ålesund (Svalbard, Norway). The equivalent black carbon (EBC, absorption inferred BC) observations at the three Arctic locations showed an overall decline of 40% from 1990 to 2009; with most change occurring during early 1990s. Model simulations confirmed declining influence on near surface BC contribution by 70% , and atmospheric BC burden by one half from the Former Soviet Union (FSU) BC source region over 16 years. In contrast, the BC contribution from the East Asia (EA) region has little influence at the surface but atmospheric Arctic BC burden increased by 3 folds. Modelled dry deposition is dominant in the Arctic during wintertime, while wet deposition prevails at all latitudes during summer. Sensitivity analyses on the dry and wet deposition schemes indicate that parameterizations need to be refined to improve on the model performance. There are limitations in the model due to simplified parameterizations and remaining model uncertainties, which requires further exploration of source region contributions, especially from growing EA source region to Arctic BC levels in the future is warranted.

[1] An aerosol black carbon (BC) data set from ongoing measurements at Zeppelin station (474 m asl), near Ny-Å lesund (10 m asl), Svalbard is reported for the period 1998 -2007. Annual average and median BC concentrations were 39 and 27 ng m À3, respectively, while monthly averages ranged from a maximum $80 ng m À3 in February/ March to a minimum 0 -10 ng m À3 from June to September. BC concentrations were calibrated by elemental carbon thermo-optical analysis. PSCF trajectory analysis indicated that BC concentrations at Zeppelin were mainly influenced by source regions in northern and central Russia. Since 2001, a small decreasing trend in BC concentration (À9.5 ng m À3 per decade) for the period to 2007 has been observed which is, however, similar to the detection limit.

The chemical composition of aerosols has been determined in 30 size-resolved samples collected using a Berner lowpressure impactor during two campaigns conducted at a coastal site in the Eastern Mediterranean in July 2000 and in January 2001. Sulfate ðSO 4 accounting for up to 38% of the total fine mass and up to 65% of the total ionic mass during both seasons. On the other hand, nitrate ðNO À 3 Þ; chloride ðCl À Þ; sodium ðNa þ Þ and calcium ðCa 2þ Þ were identified as the main components of the super-micron mode. The ionic organic compounds (including carboxylic, dicarboxylic and ketoacids) were distributed both between sub-micron and super-micron mode, indicating origin from both gas-to-particle conversion and heterogeneous reactions on pre-existing particles. The total water-soluble ionic organic fraction although accounting for only up to 1-2% of both coarse ð> 1 mmÞ and fine ðo1 mmÞ mass fractions, accounts for up to 15% of the organic carbon (OC) mass. NH þ 4 was found to be significantly correlated to non-sea-salt sulfate (nss-SO 2À 4 ), with NH þ 4 =nss-SO 2À 4 molar ratio ranging from 1.3 to 2, the lower ratio associated with transport from the W sector. Chloride depletion was observed mainly during summer and was significantly correlated with NO À 3 concentrations, with a molar ratio of 0.80, indicating the reaction of nitric acid with NaCl as the main source of NO À 3 in the area. Total ionic mass both in the fine and coarse fraction accounted for up to 58% of the total aerosol mass during both seasons. An attempt to perform a mass closure analysis indicates that nss-SO 2À 4 and organic carbon are the main components of the fine fraction with relative contributions of 38% and 16%, respectively. In the coarse fraction, the ionic part accounts for 58%, mineral dust for 32% and the remaining non-identified part of 12-30% could be partly attributed to water. r

Abstract. Soot, which is produced from biomass burning and the incomplete combustion of fossil and biomass fuels, has been linked to regional and global climate change and to negative health problems. Scientists measure the properties of soot using a variety of methods in order to quantify source emissions and understand its atmospheric chemistry, reactivity under emission conditions, interaction with solar radiation, influence on clouds, and health impacts. A major obstacle currently limiting progress is the absence of established standards or reference materials for calibrating the many instruments used to measure the various properties of soot.The current state of availability and practicability of soot standard reference materials (SRMs) was reviewed by a group of 50 international experts during a workshop in June of 2011. The workshop was convened to summarize the current knowledge on soot measurement techniques, identify the measurement uncertainties and limitations related to the lack of soot SRMs, and identify attributes of SRMs that, if developed, would reduce measurement uncertainties. The workshop established that suitable SRMs are available for calibrating some, but not all, measurement methods. The community of users of the single-particle soot-photometer (SP2), an instrument using laser-induced incandescence, identified a suitable SRM, fullerene soot, but users of instruments that measure light absorption by soot collected on filters did not. Similarly, those who use thermal optical analysis (TOA) to analyze the organic and elemental carbon components of soot were not satisfied with current SRMs. The workshop, and subsequent, interactive discussions, produced a number of recommendations for the development of new SRMs, and their implementation, that would be suitable for the different soot measurement methods.

Summary3D printers are currently widely available and very popular among the general public. However, the use of these devices may pose health risks to users, attributable to air-quality issues arising from gaseous and particulate emissions in particular. We characterized emissions from a low-end 3D printer based on material extrusion, using the most common polymers: acrylonitrile-butadiene-styrene (ABS) and polylactic acid (PLA). Measurements were carried out in an emission chamber and a conventional room. Particle emission rates were obtained by direct measurement and modeling, whereas the influence of extrusion temperature was also evaluated. ABS was the material with the highest aerosol emission rate. The nanoparticle emission ranged from 3.7·10 8 to 1.4·10 9 particles per second (# s −1 ) in chamber measurements and from 2.0·10 9 to 4.0·10 9 # s −1 in room measurements, when the recommended extruder temperature was used. Printing with PLA emitted nanoparticles at the rate of 1.0·10 7 # s −1 inside the chamber and negligible emissions in room experiments. Emission rates were observed to depend strongly on extruder temperature. The particles' mean size ranged from 7.8 to 10.5 nanometers (nm). We also detected a significant emission rate of particles of 1 to 3 nm in size during all printing events. The amounts of volatile organic and other gaseous compounds were only traceable and are not expected to pose health risks. Our study suggests that measures preventing human exposure to high nanoparticle concentrations should be adopted when using low-end 3D printers.