This study determined the bond strengths to Er:YAG laser-irradiated and non-irradiated bovine enamel of three one-step self-etch adhesives (AQ Bond Plus (AQP), G-Bond (GB), and Clearfil Tri-S Bond (TS)) and one two-step self-etch adhesive (Clearfil Megabond (MB)). Eighty SiC paper-ground bovine enamel surfaces were used, of which half were laser-irradiated. The enamel surfaces were bonded to a resin composite with each adhesive, and tensile bond strengths were determined after 24 hours. For non-irradiated enamel groups, MB achieved greater bond strength to enamel than GB and TS (p<0.05), but no significant difference was found between MB and AQP (p>0.05). For laser-irradiated enamel groups, no significant differences were found among the four adhesives (p>0.05). Additionally, for each adhesive, no significant differences were found between laser-irradiated and non-irradiated enamel. It was thus concluded that Er: YAG laser irradiation of enamel did not affect the tensile bond strength of one-step and two-step self-etch adhesives.
Objective: This study evaluated the influence of laser irradiation with a high pulse repetition rate on dentin bonding. Background Data: Although resin bonding to erbium:yttrium-aluminium-garnet (Er:YAG) laserirradiated dentin has frequently been investigated, the effects of a high pulse repetition rate have not yet been sufficiently investigated. Methods: Four groups treated under different laser conditions were evaluated in this study: 100 mJ/pulse-10 pulses per second [pps], 50 mJ/pulse-20 pps, 33 mJ/pulse-30 pps, and the unlased condition as a control. The total energy used to irradiate each group was adjusted to 1.0 W. After bovine dentin specimens were irradiated by an Er:YAG laser, acid conditioners (10% citric acid/3% ferric chloride) were applied to the lased surface. Thereafter, a PMMA rod was bonded to the lased dentin using 4-META/MMA-TBB resin, and mini-dumbbell-shaped specimens were prepared. These specimens were then tested under tensile mode and fractured surfaces were observed under scanning electron microscopy (SEM). Results: The bond strength of the unlased control was significantly higher than those of the three lased groups. Among the three lased groups, irradiation with higher output energy and lower pulse repetition rate tended to affect the higher bond strength. Upon SEM observation of the fractured surface, the lased groups showed the mixture of failure in the hybrid layer in almost part. There was no significant difference among the three lased groups. Conclusion: It can be concluded from the results of this study that a higher pulse repetition rate is not effective for resin bonding to laser-irradiated dentin.
Objective: The purpose of this study was to evaluate the influence of Er:YAG laser irradiation on the bond strength to dentine of three single-step adhesives (AQ Bond Plus, G-Bond, and Clearfil Tri-S Bond), and one two-step self-etch adhesive (Clearfil Megabond) as a control. Background Data: The vast majority of the numerous reports on resin bonding to Er:YAG-lased dentine have concluded that Er:YAG laser irradiation is less effective in terms of bond strength, because of the sub-surface damage it produces. However, its effect in combination with single-step adhesives on bonding to dentine remains to be clarified. Methods: Eighty bovine incisors were ground with silicon carbide paper to obtain a flat dentine surface, which 40 were irradiated with an Er:YAG laser. Both lased and unlased dentine was bonded to a resin composite with each adhesive. Tensile bond strength was determined after 24 h of storage in water at 37°C. Failure patterns after tensile bond testing was analyzed by scanning electron microscopy. Results: The two-step self-etch adhesive (Clearfil Megabond) showed the highest bond strength to unlased dentine, but was significantly less effective on lased dentine than the three single-step adhesives. On the other hand, AQ Bond Plus produced an effective bond strength to both lased and unlased dentine, perhaps due to its low viscosity. Conclusion: The single-step adhesives tested in this study were as effective in combination with Er:YAG-lased dentine as the two-step self-etch adhesive.3
Objective: The purpose of this study was to evaluate the hardness of the adhesive interface between resin and Er:YAG laser-irradiated bovine dentin by nano-indentation. Background Data: It has been reported that laser output energy and pulse repetition rate affect the tensile bond strength in Er:YAG laser-irradiated dentin.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.