Metal-organic frameworks (MOFs) are an important class of hybrid inorganic-organic materials. In this tutorial review, a progress report on the postsynthetic modification (PSM) of MOFs is provided. PSM refers to the chemical modification of the MOF lattice in a heterogeneous fashion. This powerful synthetic approach has grown in popularity and resulted in a number of advances in the functionalization and application of MOFs. The use of PSM to develop MOFs with improved gas sorption, catalytic activity, bioactivity, and more robust physical properties is discussed. The results reported to date clearly show that PSM is an important approach for the development and advancement of these hybrid solids.

The pendant amino groups in isoreticular metal-organic framework-3 (IRMOF-3) were subjected to postsynthetic modification with 10 linear alkyl anhydrides (O(CO(CH2)nCH3)2 (where n = 1 to 18) and the extent of conversion, thermal and structural stability, and Brunauer-Emmett-Teller (BET) surface areas of the resulting materials were probed. (1)H NMR of digested samples showed that longer alkyl chain anhydrides resulted in lower conversions of IRMOF-3 to the corresponding amide framework (designated as IRMOF-3-AM2 to IRMOF-3-AM19). Percent conversions ranged from essentially quantitative (approximately 99%, -AM2) to approximately 7% (-AM19) with IRMOF-3 samples. Modified samples were thermally stable up to approximately 430 degrees C and remained crystalline based on powder X-ray diffraction (PXRD) measurements. Under specific reaction conditions, significant conversions were obtained with complete retention of crystallinity, as verified by single-crystal X-ray diffraction experiments. Single crystals of modified IRMOF-3 samples all showed that the F-centered cubic framework was preserved. All single crystals used for X-ray diffraction were analyzed by electrospray ionization mass spectrometry (ESI-MS) to confirm that these frameworks contained the modified 1,4-benzenedicarboxylate ligand. Single crystals of each modified IRMOF-3 were further characterized by measuring the dinitrogen gas sorption of each framework to determine the effects of modification on the porosity of the MOF. BET surface areas (m(2)/g) confirmed that all modified IRMOF-3 samples maintained microporosity regardless of the extent of modification. The surface area of modified MOFs was found to correlate to the size and number of substituents added to the framework.

2-Amino-1,4-benzenedicarboxylic acid (NH(2)-BDC) has been found to be a compatible building block for the construction of two new metal-organic frameworks (MOFs) that have structures isoreticular to reported MOFs that use 1,4-benzenedicarboxylic acid (BDC) as a building block. DMOF-1-NH(2) (DABCO MOF-1-NH(2)) is a derivative of a previously studied MOF that contains two-dimensional square grids based on NH(2)-BDC and zinc(II) paddle-wheel units; the grid layers are connected by DABCO (1,4-diazabicyclo[2.2.2]octane) molecules that coordinate in the axial positions of the paddlewheel secondary-building units (SBUs). UMCM-1-NH(2) is an NH(2)-BDC derivative of UMCM-1 (University of Michigan Crystalline Material-1), a highly porous MOF reported by Matzger et al., and consists of both NH(2)-BDC and BTB (BTB = 4,4',4''-benzene-1,3,5-triyl-tribenzoate) linkers with Zn(4)O SBUs. The structure of UMCM-1-NH(2) was confirmed by single-crystal X-ray diffraction. By using NH(2)-BDC to generate these MOFs, the pendant amino groups can serve as a chemical handle that can be manipulated via postsynthetic modification with alkyl anhydrides. Reactions of each MOF and different anhydrides have been performed to compare the extent of conversion, thermal and structural stability, and Brunauer-Emmett-Teller surface areas afforded by the resulting materials. Under comparable reaction conditions, (1)H NMR of digested samples show that UMCM-1-NH(2) has conversions comparable to that of IRMOF-3, while DMOF-1-NH(2) only shows high conversions with smaller anhydrides. Under specific reaction conditions, higher conversions were obtained with complete retention of crystallinity, as verified by single-crystal X-ray diffraction experiments. The results presented here demonstrate three important findings: (a) NH(2)-BDC can be used as a surrogate for BDC in a number of MOFs thereby providing a handle for postsynthetic modification, (b) postsynthetic modification is a general strategy to functionalizing MOFs that can be applied to a variety of MOF structures, and (c) the topology and chemical/thermal stability of a MOF can influence the type of chemical reactions and reagents that can be used for postsynthetic modification.

An isoreticular metal-organic framework (IRMOF-3) containing 2-amino-1,4-benzenedicarboxylic acid (NH2–BDC) as a building block is shown to undergo chemical modification with a diverse series of anhydrides and isocyanates. The modification of IRMOF-3 by these reagents has been evidenced by using a variety of methods, including NMR and electrospray ionization mass spectrometry, and the structural integrity of the modified MOFs has been confirmed by thermogravimetric analysis, powder X-ray diffraction, and gas sorption analysis. The results show that a variety of functional groups can be introduced onto the MOF including amines, carboxylic acids, and chiral groups. Furthermore, it is shown that tert-butyl-based asymmetric anhydrides can be used to selectively deliver chemical payloads to the IRMOF. Finally, the results demonstrate that at least four different chemical modifications can be performed on IRMOF-3 and that the reaction conditions can be modulated to control the relative abundance of each group. The findings presented here demonstrate several important features of postsynthetic modification on IRMOF-3, including (1) facile introduction of a wide range of functional groups using simple reagents (e.g., anhydrides and isocyanates), (2) the introduction of multiple (as many as four different) substituents into the MOF lattice, and (3) control over reaction conditions to preserve the crystallinity and microporosity of the resultant MOFs. The findings clearly illustrate that postsynthetic modification represents a powerful means to access new MOF compounds with unprecedented chemical complexity, which may serve as the basis of multifunctional materials.

Seeing the light: Two highly porous metal–organic frameworks (MOFs) were transformed using UV light to produce MOFs with hydroxy and catechol groups through an unusual postsynthetic deprotection reaction (see scheme).