Purpose According to the study of the space flight market, there is a demand for space suborbital flights including commercial tourist flights. However, one of the challenges is to design a mission and a vehicle that could offer flights with relatively low G-loads. The project of the rocket-plane in a strake-wing configuration was undertaken to check if such a design could meet the FAA recommendation for this kind of flight. The project concept assumes that the rocket plane is released from a slowly flying carrier plane, then climbs above 100 kilometers above sea level and returns in a glide flight using a vortex lift generated by the strake-wing configuration. Such a mission has to include a flight transition during the release and return phases which might not be comfortable for passengers. Verification if FAA recommendation is fulfilled during these transition maneuvers was the purpose of this study. Design/methodology/approach The project was focused on the numerical investigation of a possibility to perform transition maneuvers mentioned above in a passenger-friendly way. The numerical simulations of a full-scale rocket-plane were performed using the simulation and dynamic stability analyzer (SDSA) software package. The influence of an elevator deflection change on flight parameters was investigated in two cases: a transition from the steep descent at high angles of attack to the level glide just after rocket-plane release from the carrier and an analogous transition after re-entry to the atmosphere. In particular, G-loads and G-rates were analyzed. Findings As a result, it was found that the values of these parameters satisfied the specific requirements during the separation and transition from a steep descent to gliding. They would be acceptable for an average passenger. Research limitations/implications To verify the modeling approach, a flight test campaign was performed. During the experiment, a rocket-plane scaled model was released from the RC model helicopter. The rocket-plane model was geometrically similar only. Froude scales were not applied because they would cause excessive technical complications. Therefore, a separate simulation of the experiment with the application of the scaled model was performed in the SDSA software package. Results of this simulation appeared to be comparable to flight test results so it can be concluded that results for the full-scale rocket-plane simulation are also realistic. Practical implications It was proven that the rocket-plane in a strake-wing configuration could meet the FAA recommendation concerning G-loads and G rates during suborbital flight. Moreover, it was proven that the SDSA software package could be applied successfully to simulate flight characteristics of airplanes flying at angles of attack not only lower than stall angles but also greater than stall angles. Social implications The application of rocket-planes in a strake-wing configuration could make suborbital tourist flights more popular, thus facilitating the development of manned space flights and contributing to their cost reduction. That is why it was so important to prove that they could meet the FAA recommendation for this kind of service. Originality/value The original design of the rocket plane was analyzed. It is equipped with an optimized strake wing and is controlled with oblique, all moving, wingtip plates. Its post-stall flight characteristics were simulated with the application of the SDSA software package which was previously validated only for angles of attack smaller than stall angle. Therefore, experimental validation was necessary. However, because of excessive technical problems caused by the application of Froude scales it was not possible to perform a conventional test with a dynamically scaled model. Therefore, the geometrically scaled model was built and flight tested. Then a separate simulation of the experiment with the application of this model was performed. Results of this separate simulation were compared with the results of the flight test. This comparison allowed to draw the conclusion on the applicability of the SDSA software for post-stall analyzes and, indirectly, on the applicability of the proposed rocket-plane for tourist suborbital flights. This approach to the experimental verification of numerical simulations is quite unique. Finally, a quite original method of the model launching during flight test experiment was applied.

Purpose The purpose of this paper is to present the methodology and approach adapted to conduct a wind tunnel experiment on the inverted joined-wing airplane flying model together with the results obtained. Design/methodology/approach General assumptions underlying the dual-use model design are presented in this paper. The model was supposed to be used for both wind tunnel tests and flight tests that significantly drive its size and internal structure. Wind tunnel tests results compared with the outcome of computational fluid dynamics (CFD) were used to assess airplane flying qualities before the maiden flight was performed. Findings Extensive data about the aerodynamic characteristics of the airplane were collected. Clean configurations in symmetric and asymmetric cases and also configurations with various control surface deflections were tested. Practical implications The data obtained experimentally made it possible to predict the performance and stability properties of the unconventional airplane and to draw conclusions on improvements in further designs of this configuration. Originality/value The airplane described in this paper differs from frequently analyzed joined-wing configurations, as it boasts a front lifting surface attached at the top of the fuselage, whereas the aft one is attached at the bottom. The testing technique involving the application of a dual-use model is also innovative.

The work concerns the research of a propulsion system for an unmanned aerial vehicle MOSUPS in joined wing configuration. Modeling, analysis and experimental research of a statically unbalanced rotor of a ducted fan propulsion system has been conducted.The aim of the analysis was to determine the critical rotational speeds of the rotor due to the probable excitation of oscillations. Due to the complex geometry, Finite Element Method has been used for the calculations. In the study, the critical frequencies (and also rotational speeds) of the rotor as well as precessional instability, flexibly mounted in the bearings have been calculated. Campbell and SAFE diagrams have been presented.Furthermore, the paper presents the idea for a device for automatic dynamic balancing of the mentioned rotor. A mechanism for changing the position of the correction weights has been developed, allowing for a long term operation of rotating parts without the need to stop the unit and correcting the unbalance.The main motivation for work was to fully understand the working conditions of the propulsion system and dynamic properties of the rotor in order to carry out a proper assessment of their impact on the safe operation of the aircraft.

This paper includes description of the technique that was applied for free-flight (drop) tests of the rocket-plane scaled model. The main aim of the experiment was to validate the numerical approach to be used to simulate the gliding flight of the rocket-plane, especially the transition between high to low angles of attack and the rocket-plane response to control. The primary goal of this paper is to show what kind of challenges must be addressed when planning the flight test campaign. This paper includes description of how the rocket-plane model was scaled and built, the model preparation, experimental design and flight procedure. This paper shows an overview of how the experiment can be planned for different scenarios and the lessons learned during the deep stall free-flight tests.

A methodology for minimization of composite panels deflections and stresses that uses a time domain nonlinear modal finite element model with two different optimization algorithms (genetic and DB algorithms) is described. The nonlinear modal formulation is based on geometrical nonlinearities rather than material nonlinearities, which does not require updating of the stiffness matrix at each time step, making it extremely time efficient when compared to commercial finite element softwares. Optimization algorithms are implemented in Matlab and can be used either with the finite element code itself or as a post-processing option. The method is applied to rectangular 10-ply symmetrically laminated plates under uniform pressure loads, with simply supported and clamped boundary conditions. The design constraints are based on the Tsai-Wu failure criterion. Results of the optimization using genetic algorithm include the influence of the initial size of population and number of generations. The DB algorithm proposed by the authors is shown to be more effective for the presented examples than the genetic algorithm.