A shortage of fresh water is one of the acute challenges facing the world today. An energy-efficient approach to converting sea water into fresh water could be of substantial benefit, but current desalination methods require high power consumption and operating costs or large-scale infrastructures, which make them difficult to implement in resource-limited settings or in disaster scenarios. Here, we report a process for converting sea water (salinity approximately 500 mM or approximately 30,000 mg l(-1)) to fresh water (salinity <10 mM or <600 mg l(-1)) in which a continuous stream of sea water is divided into desalted and concentrated streams by ion concentration polarization, a phenomenon that occurs when an ion current is passed through ion-selective membranes. During operation, both salts and larger particles (cells, viruses and microorganisms) are pushed away from the membrane (a nanochannel or nanoporous membrane), which significantly reduces the possibility of membrane fouling and salt accumulation, thus avoiding two problems that plague other membrane filtration methods. To implement this approach, a simple microfluidic device was fabricated and shown to be capable of continuous desalination of sea water (approximately 99% salt rejection at 50% recovery rate) at a power consumption of less than 3.5 Wh l(-1), which is comparable to current state-of-the-art systems. Rather than competing with larger desalination plants, the method could be used to make small- or medium-scale systems, with the possibility of battery-powered operation.

The electrowetting phenomenon is investigated in the viewpoint of the classical electrostatics. Special attention is devoted to excavating the influence of excess charge induced at the edge region of a droplet. For this, the electrostatic field around an infinite wedge is analyzed, assuming the droplet as a perfect conductor. It is shown that the Maxwell stress is concentrated on the small region comparable to the thickness of the thin dielectric film beneath the liquid droplet. On the basis of the macroscopic balance condition of the horizontal-force components at the three-phase contact line, the conventional electrowetting equation is derived. This result suggests that macroscopic changes of contact angle originated from the electrostatic force, rather than from the change of the interfacial tension at the droplet-dielectric interface. Moreover, as the apparent contact angle becomes small, the vertical component of the electrostatic force, which would oppose the reduction of contact angle, increases significantly. This can be another possible cause of the limited validity of the conventional electrowetting equation and subsequent occurrence of contact-angle saturation phenomenon. LA0263615

Direct current-dielectrophoresis (DC-DEP), the induced motion of the dielectric particles in a spatially nonuniform DC electric field, is demonstrated to be a highly efficient method to separate the microparticles by size. The locally nonuniform electric field is generated by an insulating block fabricated inside a polydimethylsiloxane microchannel. The particle experiences a negative DEP (accordingly a repulsive force) at the corners of the block, where the local electric-field strength is the strongest. Thus, the particle deviates from the streamline and the degree of deviation is dependent on the DEP force (i.e., the particle size). Combined with the electrokinetic flow, mixed polystyrene particles of a few micrometers difference in diameter can be continuously separated into distinct reservoirs. For separating target particles of a specific size, it is required to simply adjust the voltage outputs of the electrodes. A numerical model based on the Lagrangian tracking method is developed to simulate the particle motion and the results showed a reasonable agreement with the experimental data.

In this paper, we introduce a simple, straight microchannel design for a nanofluidic protein concentration device. Compared with concentration devices previously developed, the anode channel and cathode channel in this new concentration scheme are both integrated into a straight microchannel, with one inlet and one outlet. Most of the functions of a conventional two-channel concentration device can be achieved by this concentration device, and the efficiency of sample accumulation can be controlled by the dimension of the Nafion membrane. Also, the operating mechanism of this device was tested on various material combinations such as PDMS (polydimethylsiloxane) channel-glass substrate and silicon channel-PDMS substrate. Using a combined PDMSsilicon device which was sealed reversibly without plasma bonding, surface based immunoassay for concentrator-enhanced detection of clinically relevant samples such as C-reactive protein (CRP) was demonstrated. As a result, it was possible to enhance the detection sensitivity of the immunoassay by more than 500 folds compared to the immunoassay without preconcentration process.

Recently, the appeal of 2D black phosphorus (BP) has been rising due to its unique optical and electronic properties with a tunable band gap (≈0.3-1.5 eV). While numerous research efforts have recently been devoted to nano- and optoelectronic applications of BP, no attention has been paid to promising medical applications. In this article, the preparation of BP-nanodots of a few nm to <20 nm with an average diameter of ≈10 nm and height of ≈8.7 nm is reported by a modified ultrasonication-assisted solution method. Stable formation of nontoxic phosphates and phosphonates from BP crystals with exposure in water or air is observed. As for the BP-nanodot crystals' stability (ionization and persistence of fluorescent intensity) in aqueous solution, after 10 d, ≈80% at 1.5 mg mL(-1) are degraded (i.e., ionized) in phosphate buffered saline. They showed no or little cytotoxic cell-viability effects in vitro involving blue- and green-fluorescence cell imaging. Thus, BP-nanodots can be considered a promising agent for drug delivery or cellular tracking systems.