Poly(trimethylene terephthalate) (PTT) was prepared by the ring‐opening polymerization of its cyclic dimer. Antimony(III) oxide, titanium(IV) butoxide, dibutyltin oxide, and titanium(IV) isopropoxide were used as catalysts. Among the catalysts, titanium(IV) butoxide was the most effective for the same reaction conditions. A weight‐average molecular weight of 63,500 g/mol was obtained from ring‐opening poly merization at 265 °C for 2 h in the presence of 0.5 mol % titanium(IV) butoxide. The PTTs obtained from the polymerization catalyzed with increasing amounts of antimony(III) oxide showed increasing weight‐average molecular weights and reaction conversions. When 1 mol % antimony(III) oxide was used, the weight‐average molecular weight was 32,000 g/mol and the conversion was 82% after 1 h of polymerization at 265 °C. In the case of the polymer catalyzed by titanium(IV) butoxide under the same conditions, the weight‐average molecular weight and conversion were 40,000 g/mol and 77% when 0.25 mol % was used, whereas 0.5 mol % catalyst produced a weight‐average molecular weight of 27,000 g/mol and a conversion of 95%. To get an acceptable molecular weight and relatively high reaction conversion, a catalyst concentration of at least 0.5 mol % was found to be necessary, in contrast to conventional condensation polymerizations, which require only about one‐tenth of this amount of the catalyst. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6801–6809, 2006

Amorphous poly(ethylene isophthalate) (PEI) was synthesized, and was used for preparing an inclusion compound (IC) with g-cyclodextrin (g-CD). Coalesced polymer was produced by washing the PEI-g-CD-IC with hot water. Wide angle X-ray diffraction, Fourier transform infrared, and differential scanning calorimetry analyses were employed to verify formation of PEI-g-CD-IC and to compare the as-synthesized and coalesced PEI samples. These observations suggested that the conformations and morphology/ chain-packing of PEI were changed via coalescence from its g-CD inclusion compound. The glass-transition temperature of the amorphous coalesced PEI is 15-208C higher than the T g observed for the as-synthesized sample, even when observed in the second heat after cooling from well above T g at 2608C. The amorphous as-synthesized PEI retains its randomly-coiling structure, while coalesced PEI has at least partially retained, the highly extended and parallel chains from the narrow channels of the inclusion compound, resulting in better/tighter packing among the PEI chains manifested by a higher T g .

Poly(ethylene isophthalate) (PEI) was synthesized for this research with essentially a condensation polymerization of isophthalic acid and ethylene glycol catalyzed by zinc acetate and antimony trioxide. Several samples were obtained, and their characteristics were observed and compared with poly(ethylene terephthalate) (PET). The synthesized PEI samples were chemically identified by 1H NMR. Thermal analysis with differential scanning calorimetry (DSC) yielded results that indicate the samples were primarily amorphous, with a glass‐transition temperature of 55–60 °C. Molecular weights of these PEI samples were also obtained through intrinsic viscosity measurements (Mark–Houwink equation). Molecular weights varied with conditions of the polymerization, and the highest molecular weight achieved was 21,000 g/mol. Finally, the diffusion coefficient, solubility, and permeability of CO2 gas in PEI were measured and found to be substantially lower than in PET, as anticipated from their isomeric chemical structures. This is because in PET the phenyl rings are substituted in the para (1,4) positions, which allows for their facile flipping, effectively permitting gases to pass through. However, the meta‐substituted phenyl rings in PEI do not permit such ring flipping, and thus PEI may be more suitable for barrier applications. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4247–4254, 2004