Application of a multilayer Molybdenum Disulfide (MoS2) thin film as a saturable absorber was experimentally demonstrated by realizing a stable and robust passive mode-locked fiber laser via the evanescent field interaction between the light and the film. The MoS2 film was grown by chemical vapor deposition, and was then transferred to a side polished fiber by a lift-off method. Intensity-dependent optical transmission through the MoS2 thin film on side polished fiber was experimentally observed showing efficient saturable absorption characteristics. Using erbium doped fiber as an optical gain medium, we built an all-fiber ring cavity, where the MoS2 film on the side polished fiber was inserted as a saturable absorber. Stable dissipative soliton pulse trains were successfully generated in the normal dispersion regime with a spectral bandwidth of 23.2 nm and the pulse width of 4.98 ps. By adjusting the total dispersion in the cavity, we also obtained soliton pulses with a width of 637 fs in the anomalous dispersion regime near the lasing wavelength λ = 1.55 μm. Detailed and systematic experimental comparisons were made for stable mode locking of an all-fiber laser cavity in both the normal and anomalous regimes.

A new extraordinary application of deoxyribonucleic acid (DNA) thin-solid-film was experimentally explored in the field of ultrafast nonlinear photonics. Optical transmission was investigated in both linear and nonlinear regimes for two types of DNA thin-solid-films made from DNA in aqueous solution and DNA-cetyltrimethylammonium chloride (CTMA) in an organic solvent. Z-scan measurements revealed a high third-order nonlinearity with n2 exceeding 10−9 at a wavelength of 1570 nm, for a nonlinarity about five orders of magnitude larger than that of silica. We also demonstrated ultrafast saturable absorption (SA) with a modulation depth of 0.43%. DNA thin solid films were successfully deposited on a side-polished optical fiber, providing an efficient evanescent wave interaction. We built an organic-inorganic hybrid all-fiber ring laser using DNA film as an ultrafast SA and using Erbium-doped fiber as an efficient optical gain medium. Stable transform-limited femtosecond soliton pulses were generated with full width half maxima of 417 fs for DNA and 323 fs for DNA-CTMA thin-solid-film SAs. The average output power was 4.20 mW for DNA and 5.46 mW for DNA-CTMA. Detailed conditions for DNA solid film preparation, dispersion control in the laser cavity and subsequent characteristics of soliton pulses are discussed, to confirm unique nonlinear optical applications of DNA thin-solid-film.

We developed an ultra-high speed photonic sintering method involving flash white light (FWL) combined with near infrared (NIR) and deep UV light irradiation to produce highly conductive copper nano-ink film. Flash white light irradiation energy and the power of NIR/deep UV were optimized to obtain high conductivity Cu films. Several microscopic and spectroscopic characterization techniques such as scanning electron microscopy (SEM), a x-ray diffraction (XRD), and Fourier-transform infrared (FT-IR) spectroscopy were employed to characterize the Cu nano-films. Optimally sintered Cu nano-ink films produced using a deep UV-assisted flash white light sintering technique had the lowest resistivity (7.62 μΩ·cm), which was only 4.5-fold higher than that of bulk Cu film (1.68 μΩ•cm).

A new type of index-guided photonic crystal fiber is proposed to enhance chemical sensing capability by introducing a hollow high index ring defect that consists of the central air hole surrounded by a high index GeO2 doped SiO2 glass ring. Optical properties of the fundamental guided mode were numerically analyzed using the full-vector finite element method varying the design parameters of both the defects in the center and the hexagonal air-silica lattice in the cladding. Enhanced evanescent wave interaction in the holey region and lower confinement loss by an order of magnitude were achieved simultaneously, which shows a high potential in hyper sensitive fiber-optic chemical sensing applications.

We demonstrated a Q-switched fiber laser based on Tungsten Disulfide (WS 2 ) saturable absorber. The WS 2 nano-sheets were prepared by liquid phase exfoliation method and the saturable absorber was fabricated by spin-coating of few-layer WS 2 nano-sheets on a side-polished fiber for pulsed operation of a fiber laser. By inserting the absorber into an Erbiumdoped fiber laser cavity pumped by a 980 nm laser diode, a stable Qswitched laser operation was achieved with a tunable repetition rates from 82 kHz to 134 kHz depending on the applied pump power. The properties of the deposited WS 2 film was examined using scanning electron microscopic (SEM) and atomic force microscope (AFM). Detailed optical properties of the laser output are also discussed.