Skeletal muscle can bear a high load at constant length, or shorten rapidly when the load is low. This force-velocity relationship is the primary determinant of muscle performance in vivo. Here we exploited the quasi-crystalline order of myosin II motors in muscle filaments to determine the molecular basis of this relationship by X-ray interference and mechanical measurements on intact single cells. We found that, during muscle shortening at a wide range of velocities, individual myosin motors maintain a force of about 6 pN while pulling an actin filament through a 6 nm stroke, then quickly detach when the motor reaches a critical conformation. Thus we show that the force-velocity relationship is primarily a result of a reduction in the number of motors attached to actin in each filament in proportion to the filament load. These results explain muscle performance and efficiency in terms of the molecular mechanism of the myosin motor.

Muscle contraction is driven by the motor protein myosin II, which binds transiently to an actin filament, generates a unitary filament displacement or 'working stroke', then detaches and repeats the cycle. The stroke size has been measured previously using isolated myosin II molecules at low load, with rather variable results, but not at the higher loads that the motor works against during muscle contraction. Here we used a novel X-ray-interference technique to measure the working stroke of myosin II at constant load in an intact muscle cell, preserving the native structure and function of the motor. We show that the stroke is smaller and slower at higher load. The stroke size at low load is likely to be set by a structural limit; at higher loads, the motor detaches from actin before reaching this limit. The load dependence of the myosin II stroke is the primary molecular determinant of the mechanical performance and efficiency of skeletal muscle.

No abstract

Myosin II is the motor protein that produces force and shortening in muscle by ATP‐driven cyclic interactions of its globular portion, the head, with the actin filament. During each interaction the myosin head undergoes a conformational change, the working stroke, which, depending on the mechanical conditions, can generate a force of several piconewtons or an axial displacement of the actin filament toward the centre of the sarcomere of several nanometres. However, the sizes of the elementary force and length steps and their dependence on the mechanical conditions are still under question. Due to the small fraction of the ATPase cycle time myosin II spends attached to actin, single molecule mechanics failed to produce definitive measurements of the individual events. In intact frog muscle fibres, however, myosin II's working stroke can be synchronised in the few milliseconds following a step reduction in either force or length superimposed on the isometric contraction. Here we show that with 150 μs force steps it is possible to separate the elastic response from the subsequent early rapid component of filament sliding due to the working stroke in the attached myosin heads. In this way we determine how the size and the speed of the working stroke depend on the clamped force. The relation between mechanical energy and force provides a molecular basis for muscle efficiency and an estimate of the isometric force exerted by a myosin head.

Generation of force and shortening in striated muscle is due to the cyclic interactions of the globular portion (the head) of the myosin molecule, extending from the thick filament, with the actin filament. The work produced in each interaction is due to a conformational change (the working stroke) driven by the hydrolysis of ATP on the catalytic site of the myosin head. However, the precise mechanism and the size of the force and length step generated in one interaction are still under question. Here we reinvestigate the endothermic nature of the force‐generating process by precisely determining, in tetanised intact frog muscle fibres under sarcomere length control, the effect of temperature on both isometric force and force response to length changes. We show that raising the temperature: (1) increases the force and the strain of the myosin heads attached in the isometric contraction by the same amount (∼70 %, from 2 to 17 °C); (2) increases the rate of quick force recovery following small length steps (range between −3 and 2 nm (half‐sarcomere)−1) with a Q10 (between 2 and 12 °C) of 1.9 (releases) and 2.3 (stretches); (3) does not affect the maximum extent of filament sliding accounted for by the working stroke in the attached heads (10 nm (half‐sarcomere)−1). These results indicate that in isometric conditions the structural change leading to force generation in the attached myosin heads can be modulated by temperature at the expense of the structural change responsible for the working stroke that drives filament sliding. The energy stored in the elasticity of the attached myosin heads at the plateau of the isometric tetanus increases with temperature, but even at high temperature this energy is only a fraction of the mechanical energy released by attached heads during filament sliding.