We present an optical fiber supporting 36 information bearing orbital angular momentum (OAM) states spanning 9 OAM orders. We introduce design techniques to maximize the number of OAM modes supported in the fiber; while avoiding LP mode excitation. We fabricate such a fiber with an air core and an annular index profile using the MCVD process. We introduce a new technique for shaping OAM beams in free-space to obtain better coupling efficiency with fiber with annular index profiles. We excite 9 orders of OAM in the fiber, using interferometry to verify the OAM state on exiting the fiber. Using polarization multiplexing and both signs for the topological charge, we confirm support of 36 states, exploiting to our knowledge the highest number of OAM modes ever transmitted in optical fiber.

This paper proposes an all-fiber fast optical frequency-hop code division multiple access (FFH-CDMA) for high-bandwidth communications. The system does not require an optical frequency synthesizer, allowing high communication bit rates. Encoding and decoding are passively achieved by strain-tunable fiber Bragg gratings. Multiple Bragg gratings replace a frequency synthesizer, achieving a hopping rate in tens of GHz. A main lobe sinc apodization can be used in writing the gratings to enhance the system capacity and the spectrum efficiency. All network users can use the same tunable encoder/decoder design. The simultaneous utilization of the time and frequency domains offers notable flexibility in code selection. Simulations show that the encoder efficiently performs the FFH spread spectrum signal generation and that the receiver easily extracts the desired signal from a received signal for several multiple access interference scenarios. We measure the system performance in terms of bit error rate, as well as autoto cross-correlation contrast. A transmission rate of 500 Mb/s per user is supported in a system with up to 30 simultaneous users at 10 09 bit error rate. We compare FFH-CDMA to several direct sequence-CDMA systems in terms of bit error rate versus the number of simultaneous users. We show that an optical FFH-CDMA system requires new design criteria for code families, as optical device technology differs significantly from that of radio frequency communications.

Radar-based microwave imaging has been widely studied for breast cancer detection in recent times. Sensing dielectric property differences of tissues has been studied over a wide frequency band for this application. We design single- and dual-polarization antennas for wireless ultrawideband breast cancer detection systems using an inhomogeneous multilayer model of the human breast. Antennas made from flexible materials are more easily adapted to wearable applications. Miniaturized flexible monopole and spiral antennas on a 50-μm Kapton polyimide are designed, using a high-frequency structure simulator, to be in contact with biological breast tissues. The proposed antennas are designed to operate in a frequency range of 2-4 GHz (with reflection coefficient (S11) below -10 dB). Measurements show that the flexible antennas have good impedance matching when in different positions with different curvature around the breast. Our miniaturized flexible antennas are 20 mm × 20 mm. Furthermore, two flexible conformal 4 × 4 ultrawideband antenna arrays (single and dual polarization), in a format similar to that of a bra, were developed for a radar-based breast cancer detection system. By using a reflector for the arrays, the penetration of the propagated electromagnetic waves from the antennas into the breast can be improved by factors of 3.3 and 2.6, respectively.

Abstract-In this work, we present a clinical prototype with a wearable patient interface for microwave breast cancer detection. The long-term aim of the prototype is a breast health monitoring application. The system operates using multistatic time-domain pulsed radar, with 16 flexible antennas embedded into a bra. Unlike the previously reported, table-based prototype with a rigid cup-like holder, the wearable one requires no immersion medium and enables simple localization of breast surface. In comparison with the table-based prototype, the wearable one is also significantly more cost-effective and has a smaller footprint. To demonstrate the improved functionality of the wearable prototype, we here report the outcome of daily testing of the new, wearable prototype on a healthy volunteer over a 28-day period. The resulting data (both signals and reconstructed images) is compared to that obtained with our table-based prototype. We show that the use of the wearable prototype has improved the quality of collected volunteer data by every investigated measure. This work demonstrates the proof-of-concept for a wearable breast health monitoring array, which can be further optimized in the future for use with patients with various breast sizes and tissue densities.

No abstract