This paper presents a novel device for the dielectrophoretic manipulation of particles and cells. A two-level isotropic etch of a glass substrate was used to create three-dimensional ridge-like structures in micrometer-sized channels. Due to the insulating properties of glass, locally patterned regions of nonuniform electric field form near the ridges when a dc field is applied along the channel. The ridges are designed using the method of faceted prisms, such that substantially uniform fields are produced on each side of the faceted interfaces that form each ridge. The dielectrophoretic force that results from the electric field gradient near the ridges is used to affect particle motion parallel to the ridges in the absence of a bulk pressure-driven flow. Trapping and deflection of particles and continuous concentration and separation of Bacillus subtilis from a two-component sample mixture are demonstrated. The flow of B. subtilis is restricted to a selected channel of a planar, multichannel device as a result of negative dielectrophoresis arising from the presence of the insulating ridges when the applied electric field exceeds a threshold of 30 V/mm. Dielectrophoresis has a negligible impact on 200-nm-diameter polystyrene particles under the same conditions.

Towards developing rapid and portable diagnostics for detecting zoonotic diseases, we have developed microchip-based electrophoretic immunoassays for sensitive and rapid detection of viruses. Two types of microchip-based electrophoretic immunoassays were developed. The initial assay used open channel electrophoresis and laser-induced fluorescence detection with a labeled antibody to detect influenza virus. However, this assay did not have adequate sensitivity to detect viruses at relevant concentrations for diagnostic applications. Hence, a novel assay was developed that allows simultaneous concentration and detection of viruses using a microfluidic chip with an integrated nanoporous membrane. The size-exclusion properties of the in situ polymerized polyacrylamide membrane are exploited to simultaneously concentrate viral particles and separate the virus/fluorescent antibody complex from the unbound antibody. The assay is performed in two simple steps--addition of fluorescently labeled antibodies to the sample, followed by concentration of antibody-virus complexes on a porous membrane. Excess antibodies are removed by electrophoresis through the membrane and the complex is then detected downstream of the membrane. This new assay detected inactivated swine influenza virus at a concentration four times lower than that of the open-channel electrophoresis assay. The total assay time, including device regeneration, is six minutes and requires <50 microl of sample. The filtration effect of the polymer membrane eliminates the need for washing, commonly required with surface-based immunoassays, increasing the speed of the assay. This assay is intended to form the core of a portable device for the diagnosis of high-consequence animal pathogens such as foot-and-mouth disease. The electrophoretic immunoassay format is rapid and simple while providing the necessary sensitivity for diagnosis of the illness state. This would allow the development of a portable, cost-effective, on-site diagnostic system for rapid screening of large populations of livestock, including sheep, pigs, cattle, and potentially birds.

No abstract

We report a rapid, low-cost, portable microfluidic sedimentation cytometer (SeCy) for assessing the somatic cell count and fat content of milk in 15 min using a "sample-in, answer-out" approach. The system consists of 12 independent microfluidic devices, essentially flattened funnel structures, fabricated on the footprint of a single plastic compact disc (CD). Each funnel structure holds 150 μL of milk, has an inlet for milk filling and an outlet for air to escape, and ends in a narrow, closed-end microfluidic channel that facilitates packing of the cells into a column whose length is proportional to cell count. The closed-end channel provides accurate cell counts over the range 50,000->3,000,000 cells per mL. The assay separates cells and fat globules based on their densities (by differential sedimentation), concentrating white cells in the closed-end channel near the outer rim of the CD for estimation of total "cell pellet" volume, while fat globules move toward the center of disc rotation, forming a fat "band" in the funnel. After adding milk to two or more microfluidic devices, the CD is loaded onto a custom-built reader unit that spins the disc for 15 min. Two low-cost microscopes in the reader image the centrifuged cell pellet and the fat band, providing a sufficiently accurate cell count to diagnose mastitis and measuring fat content as an indication of health and nutritional status.

A uniform-field design approach can improve the performance of microanalytical, chip-based devices for a number of applications, including separations and sample preparation. The faceted prism paradigm allows the design of microfluidic devices possessing spatially uniform fields in electrokinetically driven flows. We present the first quantitative study of the velocity fields obtained using faceted interfaces between deep and shallow channel sections. Electrokinetic flows were generated in a series of wet-etch fabricated microfluidic channels. The resulting velocity fields were analyzed by particle image velocimetry and compared with simulations of the two-dimensional Laplace equation using both the designed channel geometry and the as-fabricated channel geometry. This analysis found localized differences between the designed and observed flow fields that were directly attributable to the limitations of isotropic substrate etching. Simulations using the as-fabricated channel geometry reproduced the experimental electrokinetic velocity field, quantitatively accounting for speed field variations due to the limits of the fabrication method. The electrokinetic speed fields were also compared to corresponding pressure-driven speed fields.