While superhydrophilic coatings with enhanced wetting properties have been shown to increase the pool boiling critical heat flux (CHF), the role of nanostructures on its enhancement is not clear. Here, biological templates have been used to demonstrate that wickability is the single factor dictating CHF on structured superhydrophilic surfaces. The flexibility of biotemplating using the Tobacco mosaic virus has been leveraged to create surfaces with varying scales, morphologies, and roughness factors. Their wickabilities have been quantified via the wicked volume flux, a phenomenological parameter analogous to the contact angle, and the role of wickability on CHF has been demonstrated using data from over three dozen individual surfaces. These results are repeatable and independent of the substrate material, surface fouling, structure material, morphology, and contact angle as well as the structure scale. An experimentally validated correlation for CHF has been reported on the basis of the dimensionless wickability. Additionally, the surfaces have achieved a CHF of 257 W/cm(2) for water, representing the highest reported value to date for superhydrophilic surfaces. While the role of wickability on CHF has often been cited anecdotally, this work provides a quantitative measure of the phenomena and provides a framework for designing and optimizing coatings for further enhancement.
Biotemplated nanostructures for enhanced boiling are demonstrated using the scalable nanomanufacturing of high‐surface‐area virus‐structured coatings on copper, aluminum, stainless steel, and silicon surfaces. Superhydrophilic coatings based on self‐assembly of the Tobacco mosaic virus are cheap and scalable to real‐world applications, and are shown here to enhance critical heat flux and heat transfer coefficient by up to 200%.
We report the counterintuitive mechanism of increasing boiling heat transfer by incorporating low-conductivity materials at the interface between the surface and fluid. By embedding an array of non-conductive lines into a high-conductivity substrate, in-plane variations in the local surface temperature are created. During boiling the surface temperature varies spatially across the substrate, alternating between high and low values, and promotes the organization of distinct liquid and vapor flows. By systematically tuning the peak-to-peak wavelength of this spatial temperature variation, a resonance-like effect is seen at a value equal to the capillary length of the fluid. Replacing ~18% of the surface with a non-conductive epoxy results in a greater than 5x increase in heat transfer rate at a given superheat temperature. This drastic and counterintuitive increase is shown to be due to optimized bubble dynamics, where ordered pathways allow for efficient removal of vapor and the return of replenishing liquid. The use of engineered thermal gradients represents a potentially disruptive approach to create high-efficiency and high-heat-flux boiling surfaces which are naturally insensitive to fouling and degradation as compared to other approaches.
While superhydrophobic nanostructured surfaces have been shown to promote condensation heat transfer, the successful implementation of these coatings relies on the development of scalable manufacturing strategies as well as continued research into the fundamental physical mechanisms of enhancement. This work demonstrates the fabrication and characterization of superhydrophobic coatings using a simple scalable nanofabrication technique based on self-assembly of the Tobacco mosaic virus (TMV) combined with initiated chemical vapor deposition. TMV biotemplating is compatible with a wide range of surface materials and applicable over large areas and complex geometries without the use of any power or heat. The virus-structured coatings fabricated here are macroscopically superhydrophobic (contact angle >170°) and have been characterized using environmental electron scanning microscopy showing sustained and robust coalescence-induced ejection of condensate droplets. Additionally, full-field dynamic characterization of these surfaces during condensation in the presence of noncondensable gases is reported. This technique uses optical microscopy combined with image processing algorithms to track the wetting and growth dynamics of 100s to 1000s of microscale condensate droplets simultaneously. Using this approach, over 3 million independent measurements of droplet size have been used to characterize global heat transfer performance as a function of nucleation site density, coalescence length, and the apparent wetted surface area during dynamic loading. Additionally, the history and behavior of individual nucleation sites, including coalescence events, has been characterized. This work elucidates the nature of superhydrophobic condensation and its enhancement, including the role of nucleation site density during transient operation.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.