This paper presents an analysis of the possibility of using recycled pork fat-based biodiesel as fuel for aviation turbo-engines. The analysis consists of the assessment of four blends of Jet A kerosene with 10%, 30%, 50%, and 100% biodiesel and pure Jet A that was used as reference in the study. The first part of the paper presents the physical-chemical properties of the blends: density, viscosity, flash point, freezing point, and calorific power. Through Fourier transform infrared spectroscopy (FTIR) analysis, a benchmark was performed on the mixtures of Jet A with 10%, 20%, 30%, 50%, and 100% biodiesel compared with Jet A. The second part of the paper presents the test results of these blends used for fuelling a Jet Cat P80 turbo engine at the Turbo Engines Laboratory of the Aerospace Engineering Faculty of Polyethnic University of Bucharest. These functional tests were performed using different operating regimes as follows: idle, cruise, intermediate, and maximum. For each regime, a testing period of around 1 min was selected and the engine parameters were monitored during the test execution. The burning efficiency was calculated for the maximum regime for all mixtures. To evaluate the functioning stability of the turbo engine using biodiesel, two accelerometers were mounted on the engine support that recorded the radial and axial vibrations. Moreover, to assess the burning stability and to identify other acoustic spectral components when biodiesel is used, two microphones were placed near the jet region. A comparative analysis between blends was made by taking the Jet A fuel as reference.

This paper analyzes the performances and the emissions of the JETCAT P80 microengine, when jet A jet A +  10% biodiesel (BD), jet A + 20% biodiesel, and jet A + 30% biodiesel are utilized as fuel, and to each of these combinations is added 5% of Aeroshell Oil 500. The performances will be assessed based on the engine speed, for the generated thrust force, the temperature in front of the turbine, and on the fuel flow. The paper will investigate the performances and the emissions generated by the four fuel blends burning when the engine is idle, at the cruise and at the max regime. This will be realized by maintaining each of these regimes for approximately a minute and a half. During the tests, the vibrations were monitored both radially and axially for the observation of the engine function regimes. From the measurements, the concentrations of SO2, NOx, and CH4 will be analyzed, highlighting the emissions of SO2. There were performed measurements to determine the fuel blend's density in order to transform the values of the fuel flow from liter per hour into kilogram per second. Having these data registered from the engine, a jet engine cycle analysis at max regime will be performed based on the combustion efficiency, the thermal efficiency of the engine, and the specific fuel consumption.

This paper presents a study regarding the noise reduction of the turbojet engine, in particular the jet noise of a micro turbojet engine. The results of the measurement campaign are presented followed by a performances analysis which is based on the measured data by the test bench. Within the tests, beside the baseline nozzle other two nozzles with chevrons were tested and evaluated. First type of nozzle is foreseen with eight triangular chevrons, the length of the chevrons being L = 10 percentages from the equivalent diameter and an immersion angle of I = 0 deg. For the second nozzle the length and the immersion angle were maintained, only the chevrons number were increased at 16. The micro turbojet engine has been tested at four different regimes of speed. The engine performances were monitored by measuring the fuel flow, the temperature in front of the turbine, the intake air flow, the compression ratio, the propulsion force and the temperature before the compressor. In addition, during the testing, the vibrations were measured on axial and radial direction which indicate a normal functioning of the engine during the chevron nozzles testing. Regarding the noise, it was concluded that at low regimes the noise doesn’t presents any reduction when using the chevron nozzles, while at high regimes an overall noise reduction of 2–3 dB(A) was achieved. Regarding the engine performances, a decrease in the temperature in front of the turbine, compression ratio and the intake air and fuel flow was achieved and also a drop of few percent of the propulsion force.

No abstract

This paper presents an inside-cabin acoustic evaluation of the IAR PUMA 330 helicopter, manufactured by IAR S.A. Brasov. In this study, based on the acoustic assessment inside the helicopter, areas with high noise levels are identified. In this regard, several tests were carried out in accordance with the ISO 5129 standard. In the first stage of the assessment, a measurement campaign was performed to identify the acoustic leaks from the outside noise sources propagating inside the cabin (in the door area) and the acoustic attenuation of the helicopter structure. These tests were performed on the factory runway, with the helicopter in parked position (ground tests). During the ground tests, the helicopter engines were turned off. The tests consisted of placing two loudspeakers directed towards the helicopter door and generating pink noise. Inside the helicopter, the entire door frame opening was scanned with an intensity probe to identify acoustic leaks areas. The second assessment stage was to determine the areas of the cabin with the highest levels of noise. Within the measurement campaign, 16 microphones were placed inside the cabin, at the level of the passengers’ heads, arranged in seven zones. The tests were carried out with the helicopter engines started, staying at fixed point above the ground (hovering), and then a flight test, in which all the maneuvers necessary for the use of the helicopter were performed (in-flight tests). Based on the measurement results, it was possible to highlight the noise spectral components in each of the seven areas. The noise assessment revealed high noise levels inside the cabin, having as main noise sources the transmission gear and the door area, leading to the need for reducing the noise exposure for passengers and crew, thus the need to reduce noise levels inside the helicopter.