Bacterial cellulose/polyaniline (BC/PANi) blends present a great potential for several applications. The current study evaluates the impact of using different BC matrixes (drained, freeze-dried and regenerated) and different synthesis conditions (in situ and ex situ) to improve the inherent properties of BC, which were monitored through FTIR-ATR, EDX, XRD, SEM, AFM, swelling, contact angle measurement and IGC. The employment of in situ polymerization onto drained BC presented the most conductive membrane (1.4 × 10 S/cm). The crystallinity, swelling capacity, surface energy and acid/base behavior of the BC membranes is substantially modified upon PANi incorporation, being dependent on the BC matrix used, being the freeze-dried BC blends the ones with highest crystallinity (up to 54%), swelling capacity (up to 414%) and surface energy (up to 75.0 mJ/m). Hence, this work evidenced that the final properties of the BC/PANi blends are greatly influenced by both the BC matrixes and synthesis methods employed.

We have investigated the influence of various plasma treatments of electrospun polycaprolactone (PCL) scaffolds on the adhesion and proliferation of human umbilical endothelial cells (HUVEC). The PCL scaffolds were treated in plasmas created in O2, NH3or SO2gas at identical conditions. Surface functionalization of plasma-treated samples was determined using X-ray photoelectron spectroscopy. Cell adhesion and morphology were investigated by scanning electron microscopy and the influence of plasma treatment on cell adhesion and viability was evaluated with cell viability assay (MTT assay). The results showed the highest metabolic activity of HUVEC on PCL samples treated with O2and NH3plasma. Accordingly, the cells reflected the best adhesion and morphology on O2and NH3plasma-treated PCL samples already at 3 h. Moreover, treatment with O2and NH3plasma even stimulated endothelial cell proliferation on PCL surfaces by 60% as measured at 24 h, showing significant improvement in endothelialization of this material. Contrarily, SO2plasma appeared to be less promising in comparison with O2and NH3plasma; however, it was still better than without any plasma treatment. Thus, our results importantly contribute to the biocompatibility improvement of the PCL polymer, commonly used for scaffolds in tissue engineering.

The fluorination of the polymer polyethylene terephthalate in plasma created from SF6 or CF4 gas at various pressures was investigated. The surface was analysed by X-ray photoelectron spectroscopy and water contact angle measurements, whereas the plasma was characterized by optical emission spectroscopy. The extent of the polymer surface fluorination was dependent on the pressure. Up to a threshold pressure, the amount of fluorine on the polymer surface and the surface hydrophobicity were similar, which was explained by the full dissociation of the SF6 and CF4 gases, leading to high concentrations of fluorine radicals in the plasma and thus causing the saturation of the polymer surface with fluorine functional groups. Above the threshold pressure, the amount of fluorine on the polymer surface significantly decreased, whereas the oxygen concentration increased, leading to the formation of the hydrophilic surface. This effect, which was more pronounced for the SF6 plasma, was explained by the electronegativity of both gases.

Sterilization is the final surface treatment procedure of all implantable devices and is one of the key factors which have to be considered before implementation. Since different sterilization procedures for all implantable devices influence mechanical properties as well as biological response, the influence of different sterilization techniques on titanium nanotubes was studied. Commonly used sterilization techniques such as autoclaving, ultra-violet light sterilization, hydrogen peroxide plasma sterilization as well as the not so frequently used gaseous oxygen plasma sterilization were used. Three different nanotube diameters; 15 nm, 50 nm and 100 nm were employed to study the effects of various sterilization techniques. It was observed that autoclave sterilization resulted in destruction of nanotubular features on all three studied nanotube diameters, while UV-light and both kinds of plasma sterilization did not cause any significant morphological changes on the surfaces. Differences between the sterilization techniques employed influenced cytocompatibility, especially in the case of nanotubes with 100 nm diameter.