Magnetotelluric (MT) data were used to create a three-dimensional electrical resistivity model of the Altiplano-Puna magma body (APMB) in the area surrounding Volcán Uturuncu in southern Bolivia. This volcano is at the center of a zone of surface deformation with a diameter of 150 km and persistent inflation of ~10 mm/yr. Low electrical resistivities (<3 Ωm) at a depth of 14 + 1/-3 km below sea level (16-20 km below surface) are interpreted as being due to the presence of andesite melts in the APMB, and require a mini mum melt fraction of 15%. The upper crustal resistivity structure is characterized by finite-length, dike-shaped conductors, oriented approximately east-west near sea level. A combination of dacite partial melts and aqueous fluids is required to explain the observed low-resistivity values. Geodetic data do not require any deformation in these shallow regions. The geometry of the upper surface of the APMB beneath Volcán Uturuncu is consistent with that predicted by geodynamic models that suggest that the APMB bulges upward directly beneath Volcán Uturuncu, near the measured inflation center (~3 km west of Volcán Uturuncu). Viscosity estimates from the MT-derived resistivity model gives a maximum value of 10 16 Pa•s and is consistent with models that propose diapir-like ascent of magma above the APMB. Resistivity models are compared and quantitatively correlated to seismic velocity models, showing good agreement on the spatial extent and depth of the APMB. A forward modeling study shows that the small differences in the depth to the top of the APMB between the different geophysical methods could be explained by variations in the composition of the magma body.

No abstract

The Central Andes is a key global location to study the enigmatic relation between volcanism and plutonism because it has been the site of large ignim briteforming eruptions during the past several million years and currently hosts the world's largest zone of silicic partial melt in the form of the Alti plano Puna Magma (or Mush) Body (APMB) and the Southern Puna Magma Body (SPMB). In this themed issue, results from the recently completed PLUTONS project are synthesized. This project focused an interdisciplinary study on two regions of largescale surface uplift that have been found to represent ongoing movement of magmatic fluids in the middle to upper crust. The loca tions are Uturuncu in Bolivia near the center of the APMB and Lazufre on the Chile Argentina border, on the edge of the SPMB. These studies use a suite of geological, geochemical, geophysical (seismology, gravity, surface defor ma tion, and electromagnetic methods), petrological, and geomorphological techniques with numerical modeling to infer the subsurface distribution, quantity, and movements of magmatic fluids, as well as the past history of eruptions. Both Uturuncu and Lazufre show separate geophysical anomalies in the upper, middle, and lower crust (e.g., low seismic velocity, low resistiv ity, etc.) indicating multiple distinct reservoirs of magma and/or hydrothermal fluids with different physical properties. The characteristics of the geophysical anomalies differ somewhat depending on the technique used-reflecting the different sensitivity of each method to subsurface melt (or fluid) of different compositions, connectivity, and volatile content and highlight the need for integrated, multidisciplinary studies. While the PLUTONS project has led to significant progress, many unresolved issues remain and new questions have been raised.

The Hangai Dome, Mongolia, is an unusual high-elevation, intra-continental plateau characterized by dispersed, low-volume, intraplate volcanism. Its subsurface structure and its origin remains unexplained, due in part to a lack of highresolution geophysical data. Magnetotelluric data along a ~610 km profile crossing the Hangai Dome were used to generate electrical resistivity models of the crust and upper mantle. The crust is found to be unexpectedly heterogeneous. The upper crust is highly resistive but contains several features interpreted as ancient fluid pathways and fault zones, including the South Hangai fault system and ophiolite belt that is revealed to be a major crustal boundary. South of the Hangai Dome a clear transition in crustal properties is observed which reflects the rheological differences across accreted terranes. The lower crust contains discrete zones of low-resistivity material that indicate the presence of fluids and a weakened lower crust. The upper mantle contains a large low-resistivity zone that is consistent with the presence of partial melt within an asthenospheric upwelling, believed to be driving intraplate volcanism and supporting uplift.

SUMMARY Central Mongolia is a prominent region of intracontinental surface deformation and intraplate volcanism. To study these processes, which are poorly understood, we collected magnetotelluric (MT) data in the Hangai and Gobi-Altai region in central Mongolia and derived the first 3-D resistivity model of the crustal and upper mantle structure in this region. The geological and tectonic history of this region is complex, resulting in features over a wide range of spatial scales, which that are coupled through a variety of geodynamic processes. Many Earth properties that are critical for the understanding of these processes, such as temperature as well as fluid and melt properties, affect the electrical conductivity in the subsurface. 3-D imaging using MT can resolve the distribution of electrical conductivity within the Earth at scales ranging from tens of metres to hundreds of kilometres, thereby providing constraints on possible geodynamic scenarios. We present an approach to survey design, data acquisition, and inversion that aims to bridge various spatial scales while keeping the required field work and computational cost of the subsequent 3-D inversion feasible. MT transfer functions were estimated for a 650 × 400 km2 grid, which included measurements on an array with regular 50 × 50 km2 spacing and along several profiles with a denser 5–15 km spacing. The use of telluric-only data loggers on these profiles allowed for an efficient data acquisition with a high spatial resolution. A 3-D finite element forward modelling and inversion code was used to obtain the resistivity model. Locally refined unstructured hexahedral meshes allow for a multiscale model parametrization and accurate topography representation. The inversion process was carried out over four stages, whereby the result from each stage was used as input for the following stage that included a finer model parametrization and/or additional data (i.e. more stations, wider frequency range). The final model reveals a detailed resistivity structure and fits the observed data well, across all periods and site locations, offering new insights into the subsurface structure of central Mongolia. A prominent feature is a large low-resistivity zone detected in the upper mantle. This feature suggests a non-uniform lithosphere-asthenosphere boundary that contains localized upwellings that shallow to a depth of 70 km, consistent with previous studies. The 3-D model reveals the complex geometry of the feature, which appears rooted below the Eastern Hangai Dome with a second smaller feature slightly south of the Hangai Dome. Within the highly resistive upper crust, several conductive anomalies are observed. These may be explained by late Cenozoic volcanic zones and modern geothermal areas, which appear linked to mantle structures, as well as by major fault systems, which mark terrane boundaries and mineralized zones. Well resolved, heterogeneous low-resistivity zones that permeate the lower crust may be explained by fluid-rich domains.