No abstract

ELI-Beamlines (ELI-BL), one of the three pillars of the Extreme Light Infrastructure endeavour, will be in a unique position to perform research in high-energy-density-physics (HEDP), plasma physics and ultra-high intensity (UHI) (1022W/cm2) laser–plasma interaction. Recently the need for HED laboratory physics was identified and the P3 (plasma physics platform) installation under construction in ELI-BL will be an answer. The ELI-BL 10 PW laser makes possible fundamental research topics from high-field physics to new extreme states of matter such as radiation-dominated ones, high-pressure quantum ones, warm dense matter (WDM) and ultra-relativistic plasmas. HEDP is of fundamental importance for research in the field of laboratory astrophysics and inertial confinement fusion (ICF). Reaching such extreme states of matter now and in the future will depend on the use of plasma optics for amplifying and focusing laser pulses. This article will present the relevant technological infrastructure being built in ELI-BL for HEDP and UHI, and gives a brief overview of some research under way in the field of UHI, laboratory astrophysics, ICF, WDM, and plasma optics.

The design and the early commissioning of the ELI-Beamlines laser facility’s 30 J, 30 fs, 10 Hz HAPLS (High-repetition-rate Advanced Petawatt Laser System) beam transport (BT) system to the P3 target chamber are described in detail. It is the world’s first and with 54 m length, the longest distance high average power petawatt (PW) BT system ever built. It connects the HAPLS pulse compressor via the injector periscope with the 4.5 m diameter P3 target chamber of the plasma physics group in hall E3. It is the largest target chamber of the facility and was connected first to the BT system. The major engineering challenges are the required high vibration stability mirror support structures, the high pointing stability optomechanics as well as the required levels for chemical and particle cleanliness of the vacuum vessels to preserve the high laser damage threshold of the dielectrically coated high-power mirrors. A first commissioning experiment at low pulse energy shows the full functionality of the BT system to P3 and the novel experimental infrastructure.

We use standard quantum laser theory to examine the linewidth of lasers with a four-level atomic gain medium as a function of the spontaneous emission rate into the lasing mode and the decay rates from the upper and lower lasing levels. We find that the laser linewidth ceases to exhibit the customary decrease with increased photon number when a critical photon number, proportional to the ratio of the decay rate from the lower lasing level to the rate of spontaneous emission into the lasing mode, is reached. This critical photon number would decrease as the size of the optical cavity is decreased. In addition we show that, in general, the laser linewidth depends critically on the ratio of the overall decay rates from the upper and lower lasing levels.

Linear reciprocating pin-on-plate-type wear testing has been a standard technique for the screening of orthopaedic implant materials since the early 1980s. This investigation compares a wear screening technique based on linear motion with a modern hip joint simulator based on multi-axial motion. Two groups of differently sterilized UHMWPE samples were tested. The first group of samples was sterilized by ethylene oxide (EtO) gas that caused no structural changes in the UHMWPE. The second group of samples was sterilized in nitrogen by gamma-irradiation and then subjected to a stabilization treatment that resulted in a significant level of crosslinking in the UHMWPE. When tested on the linear reciprocating wear machine, the EtO sterilized specimens (non-crosslinked linear polyethylene) showed an approximately 30% lower wear rate than the gamma-irradiated and stabilized specimens (crosslinked polyethylene). When tested on the hip simulator, the EtO sterilized specimens exhibited two to three times higher wear rates than the gamma irradiated and stabilized specimens. The ranking of wear resistance obtained with the hip simulator was strikingly different than that obtained with the linear reciprocating wear machine. This study indicates that screening wear machines based on linear motion do not correlate with multi-axial joint simulators and may produce misleading results in the prediction of clinical wear performance of UHMWPE bearing materials.