Abstract-Current nanometer technologies suffer within-die parameter uncertainties, varying workload conditions, aging, and temperature effects that cause a serious reduction on yield and performance. In this scenario, monitoring, calibration, and dynamic adaptation become essential, demanding systems with a collection of multi purpose monitors and exposing the need for light-weight monitoring networks. This paper presents a new monitoring network paradigm able to perform an early prioritization of the information. This is achieved by the introduction of a new hierarchy level, the threshing level. Targeting it, we propose a time-domain signaling scheme over a single-wire that minimizes the network switching activity as well as the routing requirements. To valídate our approach, we make a thorough analysis of the architectural trade-offs and expose two complete monitoring systems that suppose an área improvement of 40% and a power reduction of three orders of magnitude compared to previous works.

Abstract-Variabilities associated with CMOS evolution affect the yield and performance of current digital designs. FPGAs, which are widely used for fast prototyping and implementation of digital circuits, also suffer from these issues. Proactive approaches start to appear to achieve self-awareness and dynamic adaptation of these devices. To support these techniques we propose the employment of a multi-purpose sensor network. This infrastructure, through adequate use of configuration and automation tools, is able to obtain relevant data along the life cycle of an FPGA. This is realised at a very reduced cost, not only in terms of area or other limited resources, but also regarding the design effort required to define and deploy the measuring infrastructure. Our proposal has been validated by measuring inter-die and intra-die variability in different FPGA families.

Current nanometer technologies are subjected to several adverse effects that seriously impact the yield and performance of integrated circuits. Such is the case of within-die parameters uncertainties, varying workload conditions, aging, temperature, etc. Monitoring, calibration and dynamic adaptation have appeared as promising solutions to these issues and many kinds of monitors have been presented recently. In this scenario, where systems with hundreds of monitors of different types have been proposed, the need for light-weight monitoring networks has become essential. In this work we present a light-weight network architecture based on digitization resource sharing of nodes that require a time-todigital conversion. Our proposal employs a single wire interface, shared among all the nodes in the network, and quantizes the time domain to perform the access multiplexing and transmit the information. It supposes a 16% improvement in area and power consumption compared to traditional approaches.

This PhD. thesis addresses the design and implementation of signal processing applications using reconfigurable FPGA platforms. This kind of platform exhibits high logic capability, incorporates dedicated signal processing elements and provides a low cost solution, which makes it ideal for the development of signal processing applications, where intensive data processing is required in order to obtain high performance.However, the cost associated to the hardware development on these platforms is high. While the increase in logic capacity of FPGA devices allows the development of complete systems, high-performance constraints require the optimization of operators at very low level. In addition to time constraints imposed by these applications, Area constraints are also applied related to the particular device, which force to evaluate and verify a design among different implementation alternatives. The design and implementation cycle for these applications can be tedious and long, being therefore normal that new FPGA models with a greater capacity and higher speed appear before completing the system implementation. Thus, the original constraints which guided the design of the system become useless.Different methods can be used to improve the productivity when developing these applications, and consequently shorten their design cycle. This PhD. Thesis focuses on the reuse of hardware components previously designed and verified. Although conventional HDLs allow the reuse of components already defined, their specification can be improved in order to simplify the process of incorporating new design components. Thus, a first part of the PhD. Thesis will focus on the specification of designs based on predefined components. This specification improves and simplifies the process of adding components to a description, but it also seeks to improve the quality of the design specified with better configuration options and even offering to report on features of the description.Hardware reuse of a component for its integration into a system largely depends on the information it offers. In this sense the conventional HDLs only provide together with the component description, the input/output interface and a set of parameters for its configuration, while other information is usually provided by external documentation. In the second part of the Thesis we will propose a formal way of encapsulation which aims to incorporate with the component description information that can be useful for its integration into other designs. This information will include features of the own implementation, but it will also support component configuration, and even information on how to configure and connect the component to carry out a function.Finally, the fast Fourier transform (FFT) will be chosen as a well-known signal processing application. It will be used as case study to illustrate the possibilities of porposed v specification and encapsulation formalisms. The objective of the FFT design is not only to show practical examples of the proposed s...