Hybridization, especially where only variant natural lignocelluloses are combined, is fast receiving encouraging attention because it offers a range of properties that may be difficult to obtain with a single kind of reinforcement. In this study, tensile, flexural, and impact properties of hybridized kenaf/PALF-reinforced HDPE composite were studied. Sheets from which tensile, flexural, and impact specimens were cut out were produced from the compression molding of composite pellets and subsequently conditioned in an oven for 21 h at 103°C. The tensile and flexural specimens were tested according to ASTM D638 and ASTM D790 using a 5-kN INSTRON bluehill universal testing machine accordingly. While a notched Izoid impact test was conducted using a 1-J universal pendulum according to ASTM D256. All specimens were prepared at a fiber ratio of 1:1 kenaf:PALF and fiber lengths of 0.25, 0.5, 0.75, and 2 mm; fiber loadings of between 10% and 70% were utilized for the study. About 0.25 mm fiber showed the best tensile and flexural properties with a linear increase in properties up to 60% fiber loading while impact strength showed better property with 0.75 and 2 mm fiber lengths. At 0.25 mm fiber length, tensile strength of 32.24 MPa, flexural strength and modulus of 34.01 MPa and 4114.11 MPa, respectively, were observed at 60% fiber loading. Moduli results of all the composites formulated generally obeyed the ROM. SEM was used to examine the surface of composites produced. Tensile and impact strengths result showed inverse proportionality while flexural strength of the composite generally adhered to the ROM. However, a positive effect was observed in the case of composite's impact strength in respect of increasing fiber length. Thus, reduction in some mechanical properties of the composite with respect to increasing fiber length is attributed more to fiber entanglement rather than attrition.

No abstract

This article presents an experimental study on the dynamic mechanical property of hybridized Kenaf/PALF-reinforced HDPE composites. Variation in storage modulus (E′), loss modulus (E″) and damping parameter (tan δ) with fiber loading and variation in fiber length were investigated. The concept of hybridization was also discussed as it affects the dynamic properties. Initial storage modulus (E′) of all hybrids at different fibre ratios have been enormously improved compared to pure HDPE, and dependence of modulus on cellulose content of natural fibres was very clear. A lower percentage of PALF is required for hybridization with kenaf bast fibre to achieve a positive hybridization effect. Adequate hybridization could impart higher impact strength to the composite. The dynamic modulus curve showed an increase in the E′ value with increase in operating temperature up to about 130°C and is at a maximum at higher fibre loading. At lower temperatures, 60% of fibre loading had reduced the loss modulus peak of the pure HDPE. At temperature range of 30 to 65°C, incorporation of the fibres helped reduce the E″ peak of the matrix. Increasing the fibre content of the hybrids raised the damping peak with temperature. In addition, there is an increase in storage modulus with increased fibre length at room temperature up to about 65°C. Above this temperature, variation in fibre length became irrelevant up to the less viscous point of the matrix. A marginal difference in loss modulus with variation in fibre length was observed, no difference could be seen in the case of loss tangent (tan delta) in regard to variation in fibre length.

Hybridized kenaf/PALF-reinforced HDPE composite was produced and characterized. Prepared hybrids were irradiated at various doses of EBI and subsequently with 1%, 2%, and 3% concentrations of vinyltri(2-methoxy ethoxy) silane and TMPTMA as cross-linking agents. The effects of EBI on the mechanical properties of treated and untreated composites were compared. Specimens without cross-linking agents were irradiated using a 2.0 MeV EB accelerator at dose range of 10, 20, 30, 40, 60, 80, and 100 kGy. Thereafter, 10 kGy was selected to irradiate specimens that were prepared with cross-linking agents. Hybrid without the addition of any cross-linking agent showed increase in tensile strength and modulus with increase in radiation dose. Flexural strength, however, showed decline at 80 and 100 kGy. Optimum impact strength was obtained in hybrid prepared without cross-linking agents and at only 10 kGy, while 20 kGy gave superior flexural modulus. Unlike in tensile strength, silane performed better as a cross-linking agent in flexural properties than TMPTMA. Additions of cross-linking agents had less significantly improved the tensile and flexural properties of the hybrid. It was clear that HDPE self-cross-linked by radiation, making silane and TMPTMA less effective. Fractured surfaces of the composites, examined by a scanning electron microscope showed good adhesion between fiber and matrix.

No abstract