This review summarizes the results of past research on films and coatings from hemicelluloses, biopolymers that are as yet relatively unexploited commercially. The targeted uses of hemicelluloses have primarily been packaging films and coatings for foodstuffs as well as biomedical applications. Oxygen permeability of hemicellulose films, an important characteristic for food packaging, was typically comparable to values found for other biopolymer films such as amylose and amylopectin. As expected, the modification of hemicelluloses to create more hydrophobic films reduced the water vapor permeability. However, modified hemicellulose coatings intended for food still exhibited water vapor permeabilities several magnitudes higher than those of other polymers currently used for this purpose. Research on hemicelluloses for biomedical applications has included biocompatible hydrogels and coatings and material surfaces with enhanced cell affinity. Numerous possibilities exist for chemically modifying hemicelluloses, and fundamental studies of films from modified hemicelluloses have identified other potential applications, including selective membranes.

No abstract

No abstract

The partly fluorinated monomers, 2,2,2‐trifluoroethyl methacrylate (3FM), 2,2,3,3,4,4,5,5‐octafluoropentyl methacrylate (8FM), and 1,1,2,2‐tetrahydroperfluorodecyl methacrylate (17FM) have been used in the preparation of block copolymers with methyl methacrylate (MMA), 2‐methoxyethyl acrylate (MEA), and poly(ethylene glycol) methyl ether methacrylate (PEGMA) by Atom Transfer Radical Polymerization. A kinetic study of the 3FM homopolymerization initiated with ethyl bromoisobutyrate and Cu(I)Br/N‐(n‐propyl)‐2‐pyridylmethanimine reveals a living/controlled polymerization in the range 80–110 °C, with apparent rate constants of 1.6 · 10−4 s−1 to 2.9 · 10−4 s−1. Various 3FM containing block copolymers with MMA are prepared by sequential monomer addition or from a PMMA macroinitiator in all cases with controlled characteristics. Block copolymers of 3FM and PEGMA resulted in block copolymers with PDI < 1.22, whereas block copolymers from 3FM and MEA have less controlled characteristics. The block copolymers based on MMA with 8FM and 17 FM have PDI's < 1.30. The glass transition temperatures of the block copolymers are dominated by the majority monomer, as the sequential monomer addition results in too short pure blocks to induce observable microphase separation. The thermal stability of the fluorinated poly((meth)acrylate)s in inert atmosphere is less than that of corresponding nonfluorinated poly((meth)acrylate)s. The presence of fluorinated blocks significantly increases the advancing water contact angle of thin films compared to films of the nonfluorinated poly((meth)acrylate)s. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8097–8111, 2008

Polymers derived from bio‐acceptable poly(methyl methacrylate) (PMMA), poly(2‐methoxyethyl acrylate) (PMEA), and poly(oligo(ethylene glycol) methyl ether methacrylate) (PPEGMA) have been prepared via atom transfer radical polymerization (ATRP) utilizing an initiator prepared from a fluoroalkoxy‐terminated oligoethylene glycol. Polymerizations are controlled as seen by both linear first‐order kinetics and molecular weight evolution coupled with low polydispersities (<1.25) with respect to conversion. A range of ligands have been used depending upon the nature of the monomer: N‐(n‐propyl)‐2‐pyridyl‐methanimine with the methacrylates MMA and PEGMA and 1,1,4,7,10,10‐hexamethyltriethylene tetramine (HMTETA) with MEA. In all cases the use of the fluorinated initiator results in a lower apparent rate of propagation (kpapp) as compared with the more conventional and nonfluorinated initiator, ethyl 2‐bromoisobutyrate. The initiator generally also serves as an internal plasticizer lowering the glass transition temperature from the parent polymers. The surface characteristics of the fluoroinitiator containing polymers are altered compared with the nonfluorinated analogues. This is reflected in a significant increase in the advancing water contact angles of all fluoro‐containing polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5770–5780, 2007