Gas puff Z-pinches are intense sources of X-rays and neutrons but are highly susceptible to the magneto-Rayleigh-Taylor instability (MRTI). MRTI mitigation is critical for optimal and reproducible yields, motivating significant attention toward various potential mitigation mechanisms. One such approach is the external application of an axial magnetic field, which will be discussed here in the context of recent experiments on the Zebra generator (1 MA, 100 ns) at the University of Nevada, Reno. In these experiments, an annular Kr gas liner is imploded onto an on-axis deuterium target with a pre-embedded axial magnetic field Bz0 ranging from 0 to 0.3 T. The effect of Bz0 on the stability of the Kr liner is evaluated with measurements of plasma radius, overall instability amplitude, and dominant instability wavelength at different times obtained from time-gated extreme ultraviolet pinhole images. It was observed that the external axial magnetic field does not affect the implosion velocity significantly and that it reduces the overall instability amplitude and the presence of short-wavelength modes, indicating improved pinch stability and reproducibility. For the highest applied Bz0=0.3 T, the stagnation radius measured via visible streak images was found to increase. These findings are consistent with experiments reported in the literature, but here, the Bz0 required for stability, Bz0=0.13 Ipk/R0 (where Ipk is the driver peak current and R0 is the initial radius), is lower. This could be attributed to the smaller load geometry, both radially and axially. Consistent with other experiments, the cause of decreased convergence cannot be explained by the additional axial magnetic pressure and remains an open question.

Recent experiments on the 1 MA, 100 ns Zebra driver at the Nevada Terawatt Facility at the University of Nevada, Reno, investigated the compression of a deuterium target by a high-atomic-number (Ar or Kr) gas-puff liner. Pinch stability improved with axial premagnetization of 1–2 kG observed as a decrease in magneto-Rayleigh-Taylor instability growth. Implosion dynamics and stagnation conditions were studied computationally with the radiation-MHD code MACH2 using initial conditions that approximate those in the experiment. Typical average and peak implosion velocities exceeded 300 and 400 km/s, respectively, which raised the target adiabat by shock heating as the front converges on axis, at which time the target is adiabatically compressed to stagnation. Experimental fusion yields of up to 2 × 109 for Ar liner on D target implosions were measured, while with a Kr liner yields up to 1 × 1010 were measured. Higher yields in Kr compared to Ar were also calculated in 2-D MACH2 simulations. These observations will be further tested with other radiation-MHD codes, and experiments on the 1 MA LTD-III machine at UC San Diego.

No abstract

No abstract

A linear transformer driver (LTD) generator capable of delivering up to 0.9 MA current pulses with 160 ns rise time has been assembled and commissioned at University of California San Diego. The machine is an upgrade of the LTD-III pulser from Sandia National Laboratories, consisting of 40 capacitors and 20 spark gap switches, arranged in a 20-brick configuration. The driver was modified with the addition of a new trigger system, active premagnetization of the inductive cores, a vacuum chamber with multiple diagnostic ports, and a vacuum power feed to couple the driver to plasma loads. The new machine is called compact experimental system for Z-pinch and ablation research (CESZAR). The driver has a maximum bipolar charge voltage of AE100 kV, but for reliability and testing, and to reduce the risk of damage to components, the machine was operated at AE60 kV, producing 550 kA peak currents with a rise time of 170 ns on a 3.5 nH short circuit. While the peak current is scaled down due to the reduced charge voltage, the pulse shape and circuit parameters are close to the results of the cavity and power feed models but suggest a slightly higher inductance than predicted. The machine was then used to drive wire array Z-pinch and gas puff Z-pinch experiments as initial dynamic plasma loads. The evolution of the wire array Z pinch is consistent with the general knowledge of this kind of experiment, featuring wire ablation and stagnation of the precursor plasma on axis. The gas puff Z pinches were configured as a single, hollow argon gas shell, in preparation for more structured gas puff targets such as multispecies, multishell implosions. The implosion dynamics agree generally with 1D magnetohydrodynamics simulation results, but large zippering and magneto-Rayleigh-Taylor instabilities are observed. The CESZAR load region was designed to accommodate many load types to be driven by the machine, which makes it a versatile platform for studying Z-pinch plasmas. The completion of the CESZAR driver allows plasma experiments on energy coupling from LTD machines to plasma loads, instability mitigation techniques and magnetic field distributions in Z pinches, and interface dynamics in multispecies implosions.