Advances in imaging technology and computer-assisted design (CAD) have recently enabled the introduction of patient-specific knee implant designs that hold the potential to improve functional performance on the basis of patient-specific geometries, namely a patient-specific sagittal and coronal curvature, as well as enhanced bone preservation. The objective of this study was to investigate the use of a novel implant design utilizing a patient specific sagittal J-curve on the femoral component combined with a novel constant, patient-derived femoral coronal curvature and to assess tibio-femoral contact area and contact stress on a femur matched curved tibial polyethylene insert. Mean contact area and standard deviations were 81±5, 96±5 and 74±4 mm2 for the heel strike, toe off and mid-stance positions, respectively. Mean contact stress and standard deviations were 23.83±1.39, 23.27±1.14 and 20.78±0.54 MPa for the heel strike, toe off and mid-stance positions, respectively. Standard deviations of the measurements were small, not exceeding 6-7% confirming the consistency of loading conditions across different flexion angles. The results were comparable to those reported for standard, off-the-shelf fixed-bearing implants with paired femoral and tibial geometries. These data show that a constant coronal curvature can be applied to a patient-specific implant by measuring coronal curvatures across the femoral condyle in each patient and by deriving an average curvature. This novel approach combines unique benefits of patient-specific geometry with proven design concepts for minimizing polyethylene wear.

Though changes in normal joint motions and loads (e.g., following anterior cruciate ligament injury) contribute to the development of knee osteoarthritis, the precise mechanism by which these changes induce osteoarthritis remains unknown. As a first step toward identifying this mechanism, this study evaluates computational wear simulations of a patellofemoral joint specimen wear tested on a knee simulator machine. A multi-body dynamic model of the specimen mounted in the simulator machine was constructed in commercial computer-aided engineering software. A custom elastic foundation contact model was used to calculate contact pressures and wear on the femoral and patellar articular surfaces using geometry created from laser scan and MR data. Two different wear simulation approaches were investigated – one that wore the surface geometries gradually over a sequence of 10 one-cycle dynamic simulations (termed the “progressive” approach), and one that wore the surface geometries abruptly using results from a single one-cycle dynamic simulation (termed the “non-progressive” approach). The progressive approach with laser scan geometry reproduced the experimentally measured wear depths and areas for both the femur and patella. The less costly non-progressive approach predicted deeper wear depths, especially on the patella, but had little influence on predicted wear areas. Use of MR data for creating the articular and subchondral bone geometry altered wear depth and area predictions by at most 13%. These results suggest that MR-derived geometry may be sufficient for simulating articular cartilage wear in vivo and that a progressive simulation approach may be needed for the patella and tibia since both remain in continuous contact with the femur.

Quantifying muscle and joint forces over a broad range of weight bearing loads during exercise may provide data required to improve prosthetic materials and better protect against muscle and bone loss. Collectively, leg intramuscular pressure (IMP), ground reaction force (GRF), and the instrumented tibial tray force measurements provide a comprehensive assessment of leg muscle and joint biomechanical effects of gravity during exercise. Titration of body weight (BW) by lower body negative pressure (LBNP) and lower body positive pressure (LBPP) can reproducibly modulate IMP within leg muscle compartments. In addition, previous studies document peak tibial forces during various daily activities of 2.2 to 2.5 BW. The study objective was to determine the IMPs of the leg, axial compressive force on the tibia in vivo, vertical GRF, and knee range of motion during altered BW levels using LBPP and LBNP treadmill exercise. We hypothesize that peak GRF, peak tibial forces, and peak IMPs of the leg correlate linearly with percent BW, as generated across a broad range of upright LBPP and supine LBNP exercise. When running at 2.24 m/s the leg IMPs significantly increased over the loading range of 60% to 140% BW with LBPP and LBNP (P < 0.001); as expected, leg IMPs were significantly higher when running compared with standing (P < 0.001). During upright LBPP, total axial force at the knee increased linearly as a function of BW at 0.67 m/s (R(2) = 0.90) and 1.34 m/s (R(2) = 0.98). During supine LBNP, total axial force at the knee increased linearly as a function of BW at 0.67 m/s (R(2) = 0.98) and 1.34 m/s (R(2) = 0.91). The present study is the first to measure IMPs and peak tibial forces in vivo during upright LBPP, upright LBNP, and supine LBNP exercise. These data will aid the development of rehabilitation exercise hardware and prescriptions for patients and astronauts.