No abstract

A finite element (FE) model was calibrated using the data obtained from a full-scale test to failure of a 50 year old reinforced concrete (RC) railway bridge. The model was then used to assess the effectiveness of various strengthening schemes to increase the loadcarrying capacity of the bridge. The bridge was a two-span continuous single-track trough bridge with a total length of 30 m, situated in Örnsköldsvik in northern Sweden. It was tested in situ as the bridge had been closed following the construction of a new section of the railway line. The test was planned to evaluate and calibrate models to predict the load-carrying capacity of the bridge and assess the strengthening schemes originally developed by the European research project called Sustainable bridges. The objective of the test was to investigate shear failure, rather than bending failure for which good calibrated models are already available. To that end, the bridge was strengthened in flexure before the test using near-surface mounted square section carbon fiber reinforced polymer (CFRP) bars. The ultimate failure mechanism turned into an interesting combination of bending, shear, torsion, and bond failures at an applied load of 11.7 MN (2,630 kips). A computer model was developed using specialized software to represent the response of the bridge during the test. It was calibrated using data from the test and was then used to calculate the actual capacity of the bridge in terms of train loading using the current Swedish load model which specifies a 330 kN (74 kips) axle weight. These calculations show that the unstrengthened bridge could sustain a load 4.7 times greater than the current load requirements (which is over six times the original design loading), whilst the strengthened bridge could sustain a load 6.5 times greater than currently required. Comparisons are also made with calculations using codes from Canada, Europe, and the United States.

A reinforced concrete railway trough bridge in Ö rnsköldsvik, Sweden, was strengthened in bending with rods of carbonfibre-reinforced polymer and loaded to failure. The aim was to test and calibrate methods developed in the European Research Project 'Sustainable Bridges' regarding assessment and strengthening of existing bridges. A steel beam was placed in the middle of one of the two spans and was pulled downwards. Failure was reached at an applied load of 11.7 MN. It was initiated by a bond failure caused by a combined action of shear, torsion as well as bending after yielding in the longitudinal steel reinforcement and the stirrups. The bond failure led to a redistribution of the internal forces from the tensile reinforcement to the stirrups, causing the final failure. The computer models developed to simulate the loading process were improved step by step from linear shell models to more detailed models. The most developed model, a three-dimensional nonlinear finite element model with discrete reinforcement, gave accurate accounts of the response of the bridge.

Full-scale failure tests are rarely performed on structures, primarily due to their high costs and the lack of suitable test objects. This article reports the results of a 'test-to-failure' performed using a real bridge. The results obtained in such tests are valuable for assessing analytical models, updating finite element models and investigating the real behaviour of structures. The specific intention in these experiments was to study the shear failure of the bridge, which is a less wellunderstood mode of failure than is bending. To this end, it was necessary to strengthen the bridge using near-surfacemounted reinforcements made of carbon fibre-reinforced polymer bars in order to prevent bending failure. The bridge was heavily monitored during the test, using both traditional sensors such as electrical strain gauges and linear variable differential transducers alongside new monitoring systems such as fibre-optic sensors, strain rosette linear variable differential transducers and a novel photographic monitoring system. This article presents the photographic strain measurements and describes the use of the photographic tools in monitoring and characterizing the behaviour of the failure zone during the full-scale test. The strains measured using the photographic method were found to agree well with those measured using classical strain gauges. In addition, the strain contour plots generated using the photographic method provided crucial insights into the strains within the bridge's failure zone. This study was conducted under the remit of the EU 'Sustainable Bridges' Project.

<p>A 50 year-old, 121.5 m long, five span prestressed bridge was situated in the deformation zone close to a mine in Kiruna in northern Sweden. There was a risk for uneven ground deformations so the bridge was analyzed and monitored. Results and measures taken to ascertain the robustness of the bridge are presented.</p><p>The analysis resulted in an estimate that the bridge could sustain 24 mm in uneven horizontal and 83 mm in uneven vertical displacement of the two supports of a span. To be able to sustain larger deformations, the columns of the bridge were provided with joints, where shims could be inserted to counteract the settlements. To accomplish this, each one of the 18 columns of the bridge was unloaded by help of provisional steel supports. The column was then cut and a new foot was mounted to it. This made it possible to lift each individual column with two jacks, when needed, and to adjust its height by inserting or taking away shim plates.</p><p>The deformations of the bridge and the surrounding ground were monitored. The eigenmodes of the bridge were studied with accelerometers and by analysis with finite elements (FE) models. Comparison indicated good agreement between the model and the actual bridge, with calculated eigenfrequencies of 2.17, 4.15 and 4.67 Hz, for the first transversal, vertical and torsional modes, respectively. Measurements during winter resulted in higher values due to increased stiffness caused by frozen materials.</p>