Polyelectrolyte multilayer (PEM) thin films prepared using the layer-by-layer technique are proposed as a matrix for the immobilization of 1,7-bis-(4-hydroxy-3-methoxyphenyl)-1,6-heptadiene-2,5-dione (curcumin), a lipophilic model drug. The PEM assembly was based on the layer-by-layer deposition of cationic poly(diallyldimethyl-ammonium chloride) (PDADMAC) and anionic poly(4-styrene sulfonate, sodium salt) (PSS) onto a quartz slide. Curcumin was loaded by dipping the PEM film into a dilute solution of curcumin dispersed in an 80/20% v/v water/ethanol solution. Within a few minutes, the film turned bright yellow as a result of the curcumin loading. The effect of the solvent composition, curcumin concentration and film thickness on the final concentration of curcumin in the PEM films was measured by UV-vis spectroscopy. The loading of curcumin was driven by its partitioning in the PEM film, and its partitioning coefficient between the 80/20 solvent and the PEM thin film was found to have a value of 2.07 x 10(5). The extinction coefficient of curcumin loaded into PEM was calculated to 64,000 M(-1) cm(-1). Results show that the loading of curcumin into the PEM films increased with the number of deposited layers, implying that curcumin partitioned into the bulk of the thin film. The maximum curcumin dose in the PEM film was measured by exposing films of various thicknesses to a high concentration (0.01% w/v) of curcumin and recording the maximum absorbance after saturation. The films thicknesses were controlled by the number of deposited PDADMAC/PSS layers (10, 20, 30, 40, 50, and 60). Results show that increasing amounts of curcumin could be loaded into the film with an increasing number of layers and up to 8 microg/cm(2) of curcumin could be loaded into a 20-layer film. These results demonstrate that the loading of lipophilic curcumin in PEM thin films is done through a partitioning mechanism and that the PDADMAC/PSS film can be used as a loading matrix for lipophilic drugs.

No abstract

The adhesion of L929 cells to poly(e-caprolactone) (PCL) nanofibers was successfully improved via coating with polyelectrolyte multilayer thin films (PEMs), which enhanced the potential of this material as a scaffold in tissue engineering applications. With the electrostatic self-assembly technique, poly(diallyldimethylammonium chloride) (PDADMAC) and poly(sodium 4-styrene sulfonate) (PSS) were formed as four-bilayer PEMs on electrospun PCL nanofiber mats. Because PDADMAC and PSS are strong polyelectrolytes, they provided stable films with good adhesion on the fibers within a wide pH range suitable for the subsequent processes and conditions. PDADMAC and gelatin were also constructed as four-bilayer PEMs on top of the PDADMAC-and PSS-coated nanofibers with the expectation that the gelatin would improve the cell adhesion. L929 cells from mouse fibroblasts were then seeded on both uncoated and coated scaffolds to study the cytocompatibility and in vitro cell behavior. It was revealed by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay that both the uncoated and coated nanofiber mats were nontoxic as the cell viability was comparable to that of those cultured in the serum-free medium that was used as a control. The MTT assay also demonstrated that cells proliferated more efficiently on the coated nanofibers than those on the uncoated ones during the 48-h culture period. As observed by scanning electron microscopy, the cells spread well on the coated nanofibers, especially when gelatin was incorporated. The surface modification of PCL nanofiber mats described in this research is therefore an effective technique for improving cell adhesion.

A new method for the surface modification of the surface of fruits based on the Layer-by-Layer (LbL) deposition of polyelectrolyte multilayers (PEM) is presented. Mangoes fruits were coated by sequential dipping in solutions of either Poly(diallyldimethylammonium chloride), (PDADMAC) or Poly(styrene sulfonate sodium salt) (PSS). After the deposition of only few polyelectrolyte layers, the skin of the fruits was changed from hydrophobic to hydrophilic as shown by contact angles measurements decreasing from 90 to 10. Fourier transform infrared spectroscopy (FTIR) was used to confirm the deposition of the PEM coating on the fruit which was then used as a matrix to load curcumin as model compound. Ultraviolet Visible (UV-Vis) spectroscopy was used to evaluate the amount of a curcumin loaded on the fruit surface as a function of the thickness of the film by indirect leaching in ethanol. This coating method provides a new approach to dope active compound on the fruit surface such as anti-oxidant, fragrance, color and other nutriment which could increase the market value of fruits.