Mesoporous NiO films were cosensitized with a coumarin 343 dye and a proton reduction catalyst of the [Fe 2 (CO) 6 (bdt)] (bdt = benzene-1,2-dithiolate) family. Femtosecond ultraviolet−visible transient absorption experiments directly demonstrated subpicosecond hole injection into NiO from excited dyes followed by rapid (t 50% ∼ 6 ps) reduction of the catalyst on the surface with a ∼70% yield. The reduced catalyst was long-lived (2 μs to 20 ms), which may allow protonation and a second reduction step of the catalyst to occur. A photoelectrochemical device based on this photocathode produced H 2 with a Faradaic efficiency of ∼50%. Fourier transform infrared spectroscopy and gas chromatography experiments demonstrated that the observed device deterioration with time was mainly due to catalyst degradation and desorption from the NiO surface. The insights gained from these mechanistic studies, regarding development of dye−catalyst cosensitized photocathodes, are discussed. Letter http://pubs.acs.org/journal/aelccp

Self-powered photodetectors operating in the UV–visible–NIR window made of environmentally friendly, earth abundant, and cheap materials are appealing systems to exploit natural solar radiation without external power sources. In this study, we propose a new p–n junction nanostructure, based on a ZnO–Co3O4 core–shell nanowire (NW) system, with a suitable electronic band structure and improved light absorption, charge transport, and charge collection, to build an efficient UV–visible–NIR p–n heterojunction photodetector. Ultrathin Co3O4 films (in the range 1–15 nm) were sputter-deposited on hydrothermally grown ZnO NW arrays. The effect of a thin layer of the Al2O3 buffer layer between ZnO and Co3O4 was investigated, which may inhibit charge recombination, boosting device performance. The photoresponse of the ZnO–Al2O3–Co3O4 system at zero bias is 6 times higher compared to that of ZnO–Co3O4. The responsivity (R) and specific detectivity (D*) of the best device were 21.80 mA W–1 and 4.12 × 1012 Jones, respectively. These results suggest a novel p–n junction structure to develop all-oxide UV–vis photodetectors based on stable, nontoxic, low-cost materials.

In this work, we present all-oxide p-n junction core-shell nanowires (NWs) as fast and stable self-powered photodetectors. Hydrothermally grown n-type ZnO NWs were conformal covered by different thicknesses (up to 420 nm) of p-type copper oxide layers through metalorganic chemical vapor deposition (MOCVD).The ZnO NWs exhibit a single crystalline Wurtzite structure, preferentially grown along the [002] direction, and energy gap Eg=3.24 eV. Depending on the deposition temperature, the copper oxide shell exhibits either a crystalline cubic structure of pure Cu2O phase (MOCVD at 250 C) or a cubic structure of Cu2O with the presence of CuO phase impurities (MOCVD at 300 C), with energy gap of 2.48 eV.The electrical measurements indicate the formation of a p-n junction after the deposition of the copper oxide layer. The core-shell photodetectors present a photoresponsivity at 0V bias voltage up to 7.7 µA/W and time response ≤0.09 s, the fastest ever reported for oxide photodetectors in the visible range, and among the fastest including photodetectors with response limited to the UV region. The bare ZnO NWs have slow photoresponsivity, without recovery after the end of photo-stimulation. The fast time response for the core-shell structures is due to the presence of the p-n junctions, which enables fast exciton separation and charge extraction. Additionally, the suitable electronic structure of the ZnO-Cu2O heterojunction enables self-powering of the device at 0V bias voltage. These results represent a significant advancement in the development of low-cost, high efficiency and self-powered photodetectors, highlighting the need of fine tuning the morphology, composition and electronic properties of p-n junctions to maximize device performances.

Photoelectrochemical (PEC) water splitting reactions are promising for sustainable hydrogen production from renewable sources. We report here, the preparation of α-Fe 2 O 3 /Fe 3 O 4 composite films via a single-step chemical vapor deposition of [Fe(O t Bu) 3 ] 2 and their use as efficient photoanode materials in PEC setups. Film thickness and phase segregation was controlled by varying the deposition time and corroborated through cross-section Raman spectroscopy and scanning electron microscopy. The highest water oxidation activity (0.48 mA/cm 2 at 1.23 V vs RHE) using intermittent AM 1.5 G (100 mW/cm 2 ) standard illumination was found for hybrid films with a thickness of 11 μm. This phenomenon is attributed to an improved electron transport resulting from a higher magnetite content toward the substrate interface and an increased light absorption due to the hematite layer mainly located at the top surface of the film. The observed high efficiency of α-Fe 2 O 3 /Fe 3 O 4 nanocomposite photoanodes is attributed to the close proximity and establishment of 3D interfaces between the weakly ferro-(Fe 2 O 3 ) and ferrimagnetic (Fe 3 O 4 ) oxides, which in view of their differential chemical constitution and valence states of Fe ions (Fe 2+ /Fe 3+ ) can enhance the charge separation and thus the overall electrical conductivity of the layer.

No abstract