No abstract

Despite many efforts to fabricate high-aspectratio atomic force microscopy (HAR-AFM) probes for highfidelity, high-resolution topographical imaging of three-dimensional (3D) nanostructured surfaces, current HAR probes still suffer from unsatisfactory performance, low wear-resistivity, and extravagant prices. The primary objective of this work is to demonstrate a novel design of a high-resolution (HR) HAR AFM probe, which is fabricated through a reliable, costefficient benchtop process to precisely implant a single ultrasharp metallic nanowire on a standard AFM cantilever probe. The force−displacement curve indicated that the HAR-HR probe is robust against buckling and bending up to 150 nN. The probes were tested on polymer trenches, showing a much better image fidelity when compared with standard silicon tips. The lateral resolution, when scanning a rough metal thin film and single-walled carbon nanotubes (SW-CNTs), was found to be better than 8 nm. Finally, stable imaging quality in tapping mode was demonstrated for at least 15 continuous scans indicating high resistance to wear. These results demonstrate a reliable benchtop fabrication technique toward metallic HAR-HR AFM probes with performance parallel or exceeding that of commercial HAR probes, yet at a fraction of their cost.

Silver nanowires (AgNWs) hold great promise for applications in wearable electronics, flexible solar cells, chemical and biological sensors, photonic/plasmonic circuits, and scanning probe microscopy (SPM) due to their unique plasmonic, mechanical, and electronic properties. However, the lifetime, reliability, and operating conditions of AgNW-based devices are significantly restricted by their poor chemical stability, limiting their commercial potentials. Therefore, it is crucial to create a reliable oxidation barrier on AgNWs that provides long-term chemical stability to various optical, electrical, and mechanical devices while maintaining their high performance. Here we report a room-temperature solution-phase approach to grow an ultra-thin, epitaxial gold coating on AgNWs to effectively shield the Ag surface from environmental oxidation. The Ag@Au core-shell nanowires (Ag@Au NWs) remain stable in air for over six months, under elevated temperature and humidity (80 °C and 100% humidity) for twelve weeks, in physiological buffer solutions for three weeks, and can survive overnight treatment of an oxidative solution (2% H2O2). The Ag@Au core-shell NWs demonstrated comparable performance as pristine AgNWs in various electronic, optical, and mechanical devices, such as transparent mesh electrodes, surface-enhanced Raman spectroscopy (SERS) substrates, plasmonic waveguides, plasmonic nanofocusing probes, and high-aspect-ratio, high-resolution atomic force microscopy (AFM) probes. These Au@Ag core-shell NWs offer a universal solution towards chemically-stable AgNW-based devices without compromising material property or device performance.

Fused Deposition Modeling (FDM®), also known as Fused Filament Fabrication (FFF), 3D printers have been shown in numerous studies to emit ultrafine particles and volatile organic compounds (VOCs). Filament extruders, designed to create feedstocks for 3D printers, have recently come onto the consumer market for at-home hobbyists as an alternative to buying 3D printer filaments. These instruments allow for the creation of 3D printer filaments from raw plastic pellets. Given the similarity in processes and materials used by 3D printers and filament extruders, we hypothesized that filament extruders may also release ultrafine particle emissions and VOCs. An off-the-shelf filament extruder was operated in a 2 m 3 chamber using three separate feedstocks: acrylonitrile butadiene styrene (ABS) pellets, pulverized poly-lactic acid (PLA), and PLA pellets. Ultrafine particle emissions were measured in real-time using a scanning mobility particle sizer and thermal desorption tubes were used for both non-targeted and targeted analysis of VOCs present in emissions. Ultrafine particle number emission rates were comparable to those found in 3D printer studies with the greatest to least emission rates from ABS pellets, pulverized PLA, and PLA pellets, respectively. In addition, the majority of particles released were found to be ultrafine (1-100 nm), similar to 3D printer studies. A variety of VOCs were identified using the ABS feedstock, including styrene and ethylbenzene, and PLA feedstock. Styrene average mass