Modern non-contact methods for data acquisition are becoming widely used for monitoring soil erosion and for assessing soil degradation after rainfall events. Photogrammetric methods are especially favored to obtain a detailed and precise digital surface model (DSM) of the surveyed area. This paper introduces the algorithm and its Python implementation as a tool for ArcGIS software, which makes efficient automatic calculations of the volume of erosion rills or gullies. The input parameters are a DSM, and the rill edge polygon. The method was tested on an artificially created rill, where the result acquired using presented method was compared to the real volume. The comparison showed that the algorithm may underestimate the volume by 10-15%. In addition, the influence of the position of the rill edge polygon was tested on two DSMs of erosion rills. The resulting volumes of the rills, calculated on the basis of eight different edge polygons, varied by 5%. The algorithm also automates interpolation of the surface prior to erosion, which simplifies its usage in firstly monitored regions. The algorithm can also be used for volumetric analyses in other research areas and it is made available as a supplement of the publication.

An experimental laboratory setup was developed and evaluated in order to investigate detachment of soil particles by raindrop splash impact. The soil under investigation was a silty loam Cambisol, which is typical for agricultural fields in Central Europe. The setup consisted of a rainfall simulator and soil samples packed into splash cups (a plastic cylinder with a surface area of 78.5 cm2) positioned in the center of sediment collectors with an outer diameter of 45 cm. A laboratory rainfall simulator was used to simulate rainfall with a prescribed intensity and kinetic energy. Photographs of the soil’s surface before and after the experiments were taken to create digital models of relief and to calculate changes in surface roughness and the rate of soil compaction. The corresponding amount of splashed soil ranged between 10 and 1500 g m−2 h−1. We observed a linear relationship between the rainfall kinetic energy and the amount of the detached soil particles. The threshold kinetic energy necessary to initiate the detachment process was 354 J m−2 h−1. No significant relationship between rainfall kinetic energy and splashed sediment particle-size distribution was observed. The splash erosion process exhibited high variability within each repetition, suggesting a sensitivity of the process to the actual soil surface microtopography.

Field observations and consecutive modelling of soil erosion events proved to be essential for understanding and predicting erosion and sediment transport. An experimental approach often utilizes a large variety of rainfall simulators. In this technical note a complex methodology is introduced, using a mobile rainfall simulator developed at the Czech Technical University in Prague. An experimental setup with two watered plots (16 + 1 m 2 ) was established, which enables simultaneous measurements in two scales and monitoring of surface runoff, flow velocity, infiltration, sediment subsurface flow, vegetation cover effect suspended solids and phosphorus transport, surface roughness and surface evolution under rainfall and other variables. The simulator is built on a trailer transportable by car with folding arm carrying four FullJet WSQ nozzles operating independently. The configuration and water pressure 0.7 bar leads to the total watered area 2.4 x 9.6 m. Average drop size (d50) reaches 1.75 mm for 0.7 bar pressure. Christiansen uniformity index CU reaches 85%. A selection of experimental results highlights both the advantages and the weaknesses of the presented experimental setup.

In this study, the particle size distribution (PSD) of the soil sediment from topsoil obtained from soil erosion experiments under different conditions was measured. Rainfall simulators were used for rain generation on the soil erosion plots with slopes 22°, 30°, 34° and length 4.25 m. The influence of the external factors (slope and initial state) on the particle and aggregate size distribution were evaluated by laser diffractometer (LD). The aggregate representation percentage in the eroded sediment was also investigated. It has been found that when the erosion processes are intensive (steep slope or long duration of the raining), the eroded sediment contains coarser particles and lower amounts of aggregates. Three methods for the soil particle analyses were tested: (i) conventional–sieving and hydrometer method; (ii) PARIO Soil Particle Analyzer combined with sieving; and (iii) laser diffraction (LD) using Mastersizer 3000. These methods were evaluated in terms of reproducibility of the results, time demands, and usability. It was verified that the LD has significant advantages compared to other two methods, especially the short measurement time for one sample (only 15 min per sample for LD) and the possibility to destroy soil aggregates using ultrasound which is much easier than using hexametaphosphate.

No abstract