Topological acoustics has recently revolutionized fundamental concepts of acoustic propagation, giving rise to strikingly unique acoustic edge modes immune to backscattering. Despite the rapid progress in this field, simultaneous realization of reconfigurability, intelligentization, and automatic control over acoustic propagation paths is posing a great challenge. This challenge is overcome by proposing the concept of a programmable acoustic topological insulator based on two digital elements “0” or “1,” which consist of honeycomb‐lattice sonic crystals made of cylindrical rods with different diameters. The acoustic propagation paths in the topological insulators can be controlled automatically by programming different coding sequences, which arises from efficient transformation of pseudospin‐dependent edge modes on both interfaces of the digital elements. More importantly, a unique unit is experimentally fabricated that has either a “0” or “1” response automatically manipulated by an air cylinder, and design topological insulators with programmable functionality, to realize three digital acoustic devices, such as a single‐pole double‐throw switch, a single‐pole single‐throw switch, and a tunable logic gate. The proposed programmable topological insulators may enable future intelligent acoustic devices with exciting reconfigurable and programmable functionalities, which may lead to important advances in various applications, such as integrated acoustics, acoustic security, and information processing.

Cavitation is a challenging flow abnormality that leads to undesirable effects on the hydraulic behaviour of centrifugal pumps. This study analyses the cavitating flow at a normal flow rate using the shear stress transport k-ω turbulence model and the Zwart cavitation model to capture the cavitation development and spatial distribution of vapour structures within the pump. A general description of the pump head-drop phenomenon was analysed through the study of local and global flow fields. The relationship between vapour distribution and entropy generation fields was mainly investigated through the local flow analysis method. Results show that the tendency of total entropy generation rate within the impeller coincides with the pump head-drop curve. The entropy generation rate changes slightly at the early stage of the cavitation development whereas rapidly increases when the cavitation has fully developed. Cavitation development enhances the hydraulic losses and flow unsteadiness in the impeller. These hydraulic losses are located substantially at the interface of the cavity, especially at the rear portion of the cavity region.

In order to study the flow characteristics of centrifugal pumps when transporting the gas-liquid mixture, water and air were chosen as the working medium. Both numerical simulation and experimental tests were conducted on a centrifugal pump under different conditions of inlet air volume fraction (IAVF). The calculation used URANS k-epsilon turbulence model combined with the Euler-Euler inhomogeneous two-phase model. The air distribution and velocity streamline inside the impeller were obtained to discuss the flow characteristics of the pump. The results show that air concentration is high at the inlet pressure side of the blade, where the vortex will exist, indicating that the gas concentration have a great relationship with the vortex aggregation in the impeller passages. In the experimental works, pump performances were measured at different IAVF and compared with numerical results. Contributions to the centrifugal pump performance degradations were analyzed under different air-water inlet flow condition such as IAVF, bubble size, inlet pressure. Results show that pump performance degradation is more pronounced for low flow rates compared to high flow rates. Finally, pressure pulsation and vibration experiments of the pump model under different IAVF were also conducted. Inlet and outlet transient pressure signals under four IAVF were investigated and pressure pulsation frequency of the monitors is near the blade passing frequency at different IAVF, and when IAVF increased, the lower frequency signal is more and more obvious. Vibration signals at five measuring points were also obtained under different IAVF for various flow rates.

The paper presents experimental and numerical investigations performed on a single stage, single-suction, horizontal-orientated centrifugal pump in air–water two-phase non-condensable flow conditions. Experimental measurements are performed in a centrifugal pump using pressure sensor devices in order to measure the wall static pressures at the inlet and outlet pump sections for different flow rates and rotational speeds combined with several air void fraction (a) values. Two different approaches are used in order to predict the pump performance degradations and perform comparisons with experiments for two-phase flow conditions: a one-dimensional two-phase bubbly flow model, and a full “Three-Dimensional Unsteady Reynolds Average Navier–Stokes” (3D-URANS) simulation using a modified k-epsilon turbulence model combined with the Euler–Euler inhomogeneous two-phase flow description. The overall and local flow features are presented and analyzed. Limitations concerning both approaches are pointed out according to some flow physical assumptions and measurement accuracies. Some additional suggestions are proposed in order to improve two-phase flow pump suction capabilities.

Flow-induced noise causes disturbances during the operation of centrifugal pumps and also affects their performance. The pumps often work at off-design conditions, mainly at part-load conditions, because of frequent changes in the pump device system. Consequently numerous unstable phenomena occur. In low specific speed centrifugal pumps the main disturbance is the inlet backflow, which is considered as one of the most important factors of flow-induced noise and vibration. In this study, a test rig of the flow-induced noise and vibration of the centrifugal pump was built to collect signals under various operating conditions. The three-dimensional unsteady flow of centrifugal pumps was calculated based on the Reynolds-averaged equations that resemble the shear stress transport (SST) k-ω turbulence model. The results show that the blade passing frequency and shaft frequency are dominant in the spectrum of flow-induced noise, whereas the shaft component, amplitude value at shaft frequency, and peak frequencies around the shaft increase with decreasing flow. Through flow field analysis, the inlet backflow of the impeller occurs under 0.7 times the design flow. The pressure pulsation spectrum with backflow conditions validates the flow-induced noise findings. The velocity characteristics of the backflow zone at the inlet pipe were analyzed, and the dynamic characteristics of the backflow eddy during one impeller rotating period were simultaneously obtained by employing the backflow conditions. A flow visualization experiment was performed to confirm the numerical calculations.