Background Gene-environment interplay modulates Inflammatory Bowel Diseases [IBD]. Dioxin-like compounds can activate the Aryl Hydrocarbon Receptor [AhR] and alter macrophage function as well as T cell polarization. We hypothesized that attenuation of the AhR signaling pathway will ameliorate colitis in a murine model of IBD. Design DSS colitis was induced in C57BL/6 AhR null mice [AhR −/−], heterozygous mice [AhR−/+], and their wild type [WT] littermates. Clinical and morphopathological parameters were used to compare the groups. Patients: AhR pathway activation was analyzed in biopsy specimens from 25 IBD patients and 15 healthy controls. Results AhR −/− mice died before the end of the treatment. However, AhR −/+ mice exhibited decreased disease activity compared to WT mice. The AhR −/+ mice expressed less proinflammatory cytokines such as TNFα (6.1 versus 15.7 fold increase) and IL17 (23.7 versus 67.9 fold increase) and increased antiinflammatory IL-10 (2.3 fold increase) compared with the AhR+/+ mice in the colon. Colonic macrophage infiltration was attenuated in the AhR −/+ group. AhR and its downstream targets were significantly upregulated in IBD patients versus control (CYP1A1 – 19.9, and IL8-10 fold increase). Conclusion Attenuation of the AhR receptor expression resulted in a protective effect during DSS-induced colitis, while the absence of AhR exacerbated the disease. Abnormal AhR pathway activation in the intestinal mucosa of IBD patients may promote chronic inflammation. Modulation of AhR signaling pathway via the diet, cessation of smoking or administration of AhR antagonists could be viable strategies for the treatment of IBD.

In this work, an improved version of the radio frequency magnetron sputtering (RF-MS) technique was used to prepare highly adherent B-type carbonated hydroxylapatite (B-CHA) thin films. Fourier transform infrared spectroscopy (FTIR) and grazing incidence X-ray diffraction studies proved that the coatings maintained the composition and revealed the polycrystalline structure of HA. Scanning electron microscopy analysis showed that the CHA films are rough and exhibit a homogeneous microstructure. Energy-dispersive X-ray spectroscopy (EDX) mapping demonstrated a uniform distribution of the Ca and P cations while a Ca/P ratio of 1.8 was found. In addition, the FTIR experiments showed a remarkable reproducibility of the nanostructures. Human mesenchymal stem cells (hMSCs), in vitro differentiated osteoblasts, and explanted bone cells were grown over the surface of CHA coatings for periods between a few hours and 21 days. Osteoprogenitor cells maintained viability and characteristic morphology after adhesion on CHA coatings. Ki67-positive osteoblasts were the evidence of cell proliferation events. Cells showed positive staining for markers of osteoblast phenotype such as collagen type I, bone sialoprotein and osteonectin. Our data showed the formation of mineralized foci by differentiation of hMSCs to human primary osteoblasts after cultivation in osteogenic media on RF-sputtered films. The results demonstrate the capacity of B-type CHA coating to support MSCs adhesion and osteogenic differentiation ability.

The main objective of this study was to synthesize hydroxyapatite-ciprofloxacin composites using a chemical precipitation method and to evaluate the properties and in vitro release profile of the drug from the hydroxyapatite-ciprofloxacin composites. Composite characterization was achieved by FT-IR, XRD and DLS. Ciprofloxacin determination was accomplished by HPLC, resulting in good incorporation efficiency of the drug (18.13 %). The in vitro release study (Higuchi model C = K t1/2 and Ritger-Peppas model, C = K t0.6) showed a diffusion-controlled mechanism. The antibacterial activity showed that the bacterial growth inhibition zones were approximately equal for the synthesis composites and for the mechanical mixture on the Staphylococcus aureus germ. The use of hydroxyapatite, which is a biocompatible, bioactive and osteoconductive material, with ciprofloxacin, which has good antibacterial activity in this composite, makes it suitable for the development of bone grafts. Furthermore, the synthesis process allows a slow local release of the drug.

No abstract

We report on biological-derived hydroxyapatite (HA, of animal bone origin) doped with lithium carbonate (Li-C) and phosphate (Li-P) coatings synthesized by pulsed laser deposition (PLD) onto Ti6Al4V implants, fabricated by the additive manufacturing (AM) technique. After being previously validated by in vitro cytotoxicity tests, the Li-C and Li-P coatings synthesized onto 3D Ti implants were preliminarily investigated in vivo, by insertion into rabbits’ femoral condyles. The in vivo experimental model for testing the extraction force of 3D metallic implants was used for this study. After four and nine weeks of implantation, all structures were mechanically removed from bones, by tensile pull-out tests, and coatings’ surfaces were investigated by scanning electron microscopy. The inferred values of the extraction force corresponding to functionalized 3D implants were compared with controls. The obtained results demonstrated significant and highly significant improvement of functionalized implants’ attachment to bone (p-values ≤0.05 and ≤0.00001), with respect to controls. The correct placement and a good integration of all 3D-printed Ti implants into the surrounding bone was demonstrated by performing computed tomography scans. This is the first report in the dedicated literature on the in vivo assessment of Li-C and Li-P coatings synthesized by PLD onto Ti implants fabricated by the AM technique. Their improved mechanical characteristics, along with a low fabrication cost from natural, sustainable resources, should recommend lithium-doped biological-derived materials as viable substitutes of synthetic HA for the fabrication of a new generation of metallic implant coatings.