Geophysical surveys for cavity detection are one of the most common nearsurface applications. The usage of resistivity methods is also very straightforward for the air-filled underground voids, which should have theoretically infinite resistivity in the ERT image. In the first part of the paper, we deal with the comparison of detectability of the cavity by several types of the electrode arrays, the second part discusses the effect of a thin layer around the cavity itself, by means of 2D modelling. The presence of this layer deforms the resistivity image significantly as the resistive anomaly could be turned into a conductive one, in the case when the thin layer is more conductive than the background environment. From the electrical array analysis for the model situation a dipole-dipole and combined pole-dipole shows the best results among the other involved electrical arrays.

A complex of geophysical methods were used to investigate a small karst area aimed at the production of detailed geological mapping, to confirm geological localization of known sinkholes, and to find possible continuations of caves and voids below the surface. The dipole electromagnetic profiling and radiometric mapping (the gamma-ray spectrometry method) were applied to determine the spatial distribution of hard carbonate rocks and weathered valley-fill sediments. Detailed high-definition magnetometry was carried out at selected sites in the studied region with the aim of distinguishing between sinkholes and man-made lime-kilns, pits where limestone was heated and transformed into lime. The microgravity and the electrical-resistivity tomography (ERT) methods were used to create high-resolution images of the underground cave. The results of ERT and the geological survey were used as an initial model for gravity modeling. Subsurface cavities of various sizes are contrasting geophysical objects, and the electrical resistivity can range from very conductive to relatively resistive depending on the composition of the filling materials. The interpretation of resistivity properties is not always straightforward. We must distinguish air-filled (high-resistivity) and loamy water-filled (low-resistivity) cavities and fractures. The combined geophysical methodology permits us to determine a more accurate near-surface geological model, in our case the parallel interpretation of a strong conductive anomaly in the ERT inversion and a predominant density decrease in the gravity modelling yield the presence of cavities at depths approximately of 50 to 60 m below the surface.

Abstract:The paper describes the application of geophysical prospecting techniques for estimation of the fault's inclination. The field survey was carried out across the Muráň fault structure in the Slovenské rudohorie Mts (central Slovakia). Three different geophysical methods were used to map the fault zone: Electrical Resistivity Tomography (ERT), induced polarization (IP) and radon emanometry. All these methods have been used to locate the fault zone area, but the principal aims of this research are to test the efficiency of the 2D ERT technique to recognize the geometrical characterization of the fault and to improve our tectonic knowledge of the investigated area. For the synthetic cases, three geometric contexts were modelled at 60, 90 and 120 degrees and computed with the l 2 norm inversion method, the l 1 norm with standard horizontal and vertical roughness filter and the l 1 norm with diagonal roughness filter. In the second phase this geophysical methodology was applied to fieldwork data. Our results confirm that the ERT technique is a valuable tool to image the fault zone and to characterize the general geometry, but also the importance of setting up the right inversion parameters. The main contribution of the geophysical investigations in this case was the determination of the location and confirmation of the inclination of the Muráň fault. The result of this study is the ability to make a visual estimation of the direction and dip of the fault. Pursuant to this work the dipole-dipole electrode configuration produces the best resolution, particularly for the location of vertical and dipping structures. The advantage of this array is that it shows the ability to assess the trend of the dip and therefore it can be strongly recommended. The result is also a case study of a small scale tectonic survey involving geophysical methods.

Geophysical methods offer a broad spectrum of information by dealing with slope deformations. The electrical resistivity tomography (ERT) method is mainly applied for spatial localization of the landslide body and depicting the shear zone position. This article presents the application of the ERT method for the landslide hazardous areas by means of numerical modelling. Four different synthetic models with very small resistivity contrast (30 Ohm.m/50 Ohm.m), where each model represents a different type of slope deformation, were tested by several factors affecting the final inverse model: measurement point density, L1 and L2 norm and L-norm roughness filter components. The higher measurement points density helps mainly to detect the boundaries at greater depths. Inverse models computed using the L1 norm bring satisfactory results for compact anomalous bodies, i.e. water saturated landslide body. In the case of subtle conductive zones, i.e. shear planes, the L2 norm based inversion is recommended. For enhanced reconstruction of skewed anomalous objects, roughness filter including a diagonal component produces more accurate inverse image. The article also demonstrates the ability of the ERT method to detect and describe the shape of the slope deformation even by a relative subtle resistivity contrast.

This contribution is focused on a common utilization of microgravimetry (very precise and detailed gravimetry) and geoeletrical methods (ground penetrating radar and electric resistivity tomography) in the detection of subsurface cavities in non-destructive archaeological prospection. Both methods can separately detect such kind of subsurface objects, but their complementary and at the same time an eliminating aspect can be very helpful in the interpretation of archaeogeophysical datasets. These properties were shown in various published case-studies. Here we present some more typical examples. Beside this, we present here for a first time an application of the electric resistivity tomography in the interior of a building (a church) in Slovakia. We also demonstrate an example with an extremely small acquisition step in microgravity as a trial for the detection of cavities with very small dimensions -in this case small separated spaces for coffins as a part of the detected crypt (so called columbarium). Unfortunately, these cavities were too small to be reliably detected by the microgravity method. We have tried the well-known 3D Euler deconvolution method to obtain usable depth estimates from the acquired anomalous gravity field. Results from this method were in the majority of cases plausible (sometimes little bit too shallow), when compared with the results from the ground penetrating radar.In one selected example, the 3D Euler solutions were too deep and in the present stage of study we cannot well explain this situation. In general, all presented results support an important role of common combination of several geophysical methods, when searching for subsurface cavities in non-destructive archaeological prospection.