No abstract

Metallic bipolar plates (BPPs) are key components in the proton-exchange membrane fuel cell (PEMFC), which can replace traditional fossil fuels as a kind of clean energy. However, these kinds of plates, characterized by micro-channels with a high ratio between depth and width, are difficult to fabricate with an ultra-thin metallic sheet. Then, ultrasonic-vibration-assisted stamping is performed considering the acoustic softening effect. Additionally, the influence of various vibration parameters on the forming quality is analyzed. The experimental results show that ultrasonic vibration can obviously increase the channel depth. Among the vibration parameters, the vibration power has the maximum influence on the depth, the vibration interval time is the second, and the vibration duration time is the last. In addition, the rolling direction will affect the channel depth. When the micro-channels are parallel to the rolling direction, the depth of a micro-channel is the largest. This means that the developed ultrasonic-vibration-assisted stamping process is helpful for improving the forming limitation of micro-channels used for the bipolar plates in PEMFC.

Ultrasonic vibration (UV) is widely used in the forming, joining, machining process, etc. for the acoustic softening effect. For parts with small dimensions, UV with limited output energy is very suitable for the microforming process and has been gaininf more and more attention. In this investigation, UV-assisted uniaxial tensile experiments were carried out utilizing GB 5052 thin sheets of different thicknesses and grain sizes, respectively. The coupling effects of UV and the specimen dimension on the properties of the material were analyzed from the viewpoint of acoustic energy in activating dislocations. A reduction of flow stress was found for the existing acoustic softening effects of UV. Additionally, the residual effects of UV were demonstrated when UV was turned off. The uniform deformation ability of thin sheet could be improved by increasing the hardening exponent with UV. The experimental results indicate that UV is very helpful in improving the forming limit in microsheet forming, e.g., microbulging and deep drawing processes.

Laser irradiation is a popular method to produce microtextures on metal surfaces. However, the common laser-produced microtextures were hierarchical (multiscale), which may limit their applicability. In this paper, a method of two-step laser irradiation, combining first-step strong ablation and sequentially second-step gentle ablation, was presented to produce micron-rough surface with single-scale microtextures. The effect of laser fluence on the Ti–6Al–4V surface morphology and wettability were investigated in detail. The morphology results revealed that the microtextures produced using this method gradually evolved from multiscale to single-scale meanwhile from microprotrusions to microholes with increasing the second-step laser fluence from 0.0 to 2.4 J/cm2. The wettability and EDS/XPS results indicated that attributing to the rich TiO2 content and micron roughness produced by laser irradiation, all the two-step laser-irradiated surfaces exhibited superhydrophilicity. In addition, after silanization, all these superhydrophilic surfaces immediately turned to be superhydrophobic with close water contact angles of 155–162°. However, due to the absence of nanotextures, the water-rolling angle on the superhydrophobic surfaces with single-scale microtextures distinctly larger than those with multiscale ones. Finally, using the two-step laser-irradiation method and assisted with silanization, multifunctional superhydrophobic Ti–6Al–4V surfaces were achieved, including self-cleaning, guiding of the water-rolling direction and anisotropic water-rolling angles (like the rice-leaf), etc.

To reduce the weight and volume, and extend the life of the proton-exchange membrane fuel cell (PEMFC) which is considered as a kind of near zero emission green energy, titanium ultra-thin sheet is selected to fabricate the core components- bipolar plates for its smaller density and high corrosion resistance. In order to break through the bottlenecks in the manufacture of micro channels with big ratio of depth and width, a kind of three-stage stamping was investigated for its characters such as high productivity and low cost, etc. FE simulation and optimization of three-stage stamping was carried out considering the reduction of thickness by analyzing the effect of the radius of punch and female die corner, punch displacement and ratio of rib and channel width, etc. Then, the mold was designed, and experiments were performed using a servo drive machine. The arc design of punch end in the first stage can decrease the reduction of thickness from 47–22%. The best ratio between rib and channel width is 0.4–0.6, and radius of final channel corner is 0.15mm. Experimental results of three-stage stamping show that the max. reduction of thickness is about 24%, which is similar with that obtained from FE simulation. Microstructure with uniform small grain size and high surface quality are both helpful for improving the properties of bipolar plates required by PEMFC. This means that the developed three-stage stamping process is very suitable for massive manufacturing the bipolar plates with titanium ultra-thin sheet.