Alginate hydrogels are currently being employed and explored for a broad range of medical applications including cell encapsulation, drug delivery, and tissue engineering. In these capacities, knowledge of the mechanical and material properties of the hydrogels and the properties that govern and influence them is necessary to adequately design and effectively use these systems. Although much is known about the mechanical properties of alginate in compression and shear, little is known about the tensile characteristics. Thus, an extensive tensile assessment of alginate hydrogels was completed as a function of alginate type, formulation, gelling conditions, incubation, and strain rate. In general, the initial tensile behavior and properties of alginate hydrogels were highly dependent on the choice of the alginate polymer and how it was processed. Specifically, high guluronic acid containing alginate polymers yielded stronger, more ductile hydrogels than high mannuronic acid containing alginates. The ultimate stress, ultimate strain, and tensile modulus were decreased by increased phosphate concentrations, solution reconstitution with phosphate buffered saline instead of culture media, and peptide modification. Incubation of hydrogels for at least 7 days diminished many of the initial tensile property differences associated with formulation and gelling conditions. Overall, by controlling the specific alginate polymer and processing methods, a wide range of tensile properties are available from these hydrogels.

One of the obstacles to the potential clinical utility of bioengineered skeletal muscle is its limited force generation capacity. Since engineered muscle, unlike most native muscle tissue, is composed of relatively short myofibers, we hypothesized that its force production and transmission would be profoundly influenced by cell-matrix interactions. To test this hypothesis, we systematically varied the matrix protein type (collagen I/fibrin/Matrigel) and concentration in engineered, hydrogelbased neonatal rat skeletal muscle bundles and assessed the resulting tissue structure, generation of contractile force, and intracellular Ca 2+ handling. After two weeks of culture, the muscle bundles consisted of highly aligned and cross-striated myofibers and exhibited standard force-length and force-frequency relationships achieving tetanus at 40 Hz. The use of 2 mg/ml fibrin (control) yielded isometric tetanus amplitude of 1.4±0.3 mN as compared to 0.9±0.4 mN measured in collagen I-based bundles. Higher fibrin and Matrigel concentrations synergistically yielded further increase in active force generation to 2.8±0.5 mN without significantly affecting passive mechanical properties, tetanus-to-twitch ratio, and twitch kinetics. Optimized matrix composition yielded significant cellular hypertrophy (protein/DNA ratio=11.4±4.1 vs. 6.5±1.9 μg/μg in control) and a prolonged Ca 2+ transient half-width (Ca 50 =232.8±33.3 vs. 101.7±19.8 ms). The use of growth-factor-reduced Matrigel instead of standard Matrigel did not alter the obtained results suggesting enhanced cell-matrix interactions rather than growth factor supplementation as an underlying cause for the measured increase in contractile force. In summary, biomaterial-based manipulation of cell-matrix interactions represents an important target for improving contractile force generation in engineered skeletal muscle.

The transition of a muscle cell from a differentiated myotube into an adult myofiber is largely unstudied. This is primarily due to the difficulty of isolating specific developmental stimuli in vivo and the inability to maintain viable myotubes in culture for sufficient lengths of time. To address these limitations, a novel method for rapidly generating three-dimensional engineered muscles using fibrin gel casting has been developed. Myoblasts were seeded and differentiated on top of a fibrin gel. Cell-mediated contraction of the gel around artificial anchors placed 12 mm apart culminates 10 days after plating in a tubular structure of small myotubes (10-microm diameter) surrounded by a fibrin gel matrix. These tissues can be connected to a force transducer and electrically stimulated between parallel platinum electrodes to monitor physiological function. Three weeks after plating, the three-dimensional engineered muscle generated a maximum twitch force of 329 +/- 26.3 microN and a maximal tetanic force of 805.8 +/- 55 microN. The engineered muscles demonstrated normal physiological function including length-tension and force-frequency relationships. Treatment with IGF-I resulted in a 50% increase in force production, demonstrating that these muscles responded to hormonal interventions. Although the force production was maximal at 3 wk, constructs can be maintained in culture for up to 6 wk with no intervention. We conclude that fibrin-based gels provide a novel method to engineer three-dimensional functional muscle tissue and that these tissues may be used to model the development of skeletal muscle in vitro.

SUMMARYOur purpose was to engineer three-dimensional skeletal muscle tissue constructs from primary cultures of adult rat myogenic precursor cells, and to measure their excitability and isometric contractile properties. The constructs, termed myooids, were muscle-like in appearance, excitability, and contractile function. The myooids were 12 mm long and ranged in diameter from 0.1 to 1 mm. The myooids were engineered with synthetic tendons at each end to permit the measurement of isometric contractile properties. Within each myooid the myotubes and fibroblasts were supported by an extracellular matrix generated by the cells themselves, and did not require a preexisting scaffold to define the size, shape, and general mechanical properties of the resulting structure. Once formed, the myooids contracted spontaneously at approximately 1 Hz, with peak-to-peak force amplitudes ranging from 3 to 30 N. When stimulated electrically the myooids contracted to produce force. The myooids (n ϭ 14) had the following mean values: diameter of 0.49 mm, rheobase of 1.0 V/mm, chronaxie of 0.45 ms, twitch force of 215 N, maximum isometric force of 440 N, resting baseline force of 181 N, and specific force of 2.9 kN/m 2 . The mean specific force was approximately 1% of the specific force generated by control adult rat muscle. Based on the functional data, the myotubes in the myooids appear to remain arrested in an early developmental state due to the absence of signals to promote expression of adult myosin isoforms.