Flexible and stretchable polyurethane/carbon nanotube composite with strain detection ability was used for human breath monitoring. The composite material consisted of a network of multiwalled carbon nanotubes and thermoplastic high elastic polyurethane. It was found that elongation of the composite led to a macroscopic increase in electrical resistance, which can be used as a principle for applied strain detection. This detection was reversible, durable, and sensitive with gauge factor reaching very promising value, as, for example, ~46 at applied deformation of 8.7%. Further, the composite could be elongated to very large extend of deformation without discontinuity in measured resistance change reaching gauge factor ~ 450 at composite mechanical break at ~300% of strain. Sensor durability was also confirmed by sine wave deformation cycling when any decrease in the sensor properties for more than 103 cycles was observed. Simultaneously, the prepared composite possessed other utility properties also and was considered as multifunctional when it was tested as an organic solvent vapor sensor, an element for Joule heating and finally as a microstrip antenna.

Wearable electronic sensor was prepared on a light and flexible substrate. The breathing sensor has a broad assumption and great potential for portable devices in wearable technology. In the present work, the application of a flexible thermoplastic polyurethane/multiwalled carbon nanotubes (TPU/MWCNTs) strain sensor was demonstrated. This composite was prepared by a novel technique using a thermoplastic filtering membrane based on electrospinning technology. Aqueous dispersion of MWCNTs was filtered through membrane, dried and then welded directly on a T-shirt and encapsulated by a thin silicone layer. The sensing layer was also equipped by electrodes. A polymer composite sensor is capable of detecting a deformation by changing its electrical resistance. A T-shirt was capable of analyzing a type, frequency and intensity of human breathing. The sensitivity to the applied strain of the sensor was improved by the oxidation of MWCNTs by potassium permanganate (KMnO4) and also by subsequent application of the prestrain.

A wearable and stretchable strain sensor with a gauge factor above 23 was prepared using a simple and effective technique. Conducting nanocomposite strands were prepared from styrene-b-(ethylene-co-butylene)-b-styrene triblock copolymer (SEBS) and carbon black (CB) through a solvent-processing method that uses a syringe pump. This novel nanocomposite preparation technique is a straightforward and cost-effective process and is reported in the literature for the first time. The work included two stages: the flexible nanocomposite preparation stage and the piezoresistive sensor stage. Depending on its molecular structure, the thermoelastic polymer SEBS is highly resilient to stress and strain. The main aim of this work is to fabricate a highly flexible and piezoresistive nanocomposite fibre/strand. Among the prepared composites, a composite corresponding to a composition just above the percolation threshold was selected to prepare the strain sensor, which exhibited good flexibility and conductivity and a large piezoresistive effect that was linearly dependent on the applied strain. The prepared nanocomposite sensor was stitched onto a sports T-shirt. Commercially available knee and elbow sleeves were also purchased, and the nanocomposite SEBS/CB strands were sewn separately on the two sleeves. The results showed a high sensitivity of the sensing element in the case of breathing activity (normal breathing, a 35% change, and deep breathing at 135%, respectively). In the case of knee and elbow movements, simultaneous measurements were performed and found that the sensor was able to detect movement cycles during walking.

We prepared electroactive PVDF membranes, which were subjected to mechanical as well as dual electro–mechanical signals and their responses were detected by the evoked electrical pulses. The aim was to obtain primarily electric energy that could be used for light signalling, sensing of the membrane properties and membrane motion detection. The obtained data showed the unique as well as usable properties of PVDF membranes. From this point of view, the gain and analysis of the electrical responses to combined electro–mechanical loads of PVDF membranes have been important in terms of identifying the mechanism. The detected electrical response of the PVDF membrane to their electro–mechanical pulses also indicated the possibility of using this phenomenon. Among others, it suggests monitoring of membrane fouling and use for a self-cleaning mechanism.

The design of a unipole and a dual band F-shaped antenna was conducted to find the best parameters of prepared antenna. Antenna radiator part is fully made of polymer and nonmetal base composite. Thermoplastic polyurethane (PU) was chosen as a matrix and multi-wall carbon nanotubes (MWCNT) as an electrical conductive filler, which creates conductive network. The use of the composite for the antenna has the advantage in simple preparation through dip coating technique. Minor disadvantage is the usage of solvent for composite preparation. Composite structure was used for radiator part of antenna. The antenna operates in 2.45 and 5.18 GHz frequency bands. DC conductivity of our PU/MWCNT composite is about 160 S/m. With this material, a unipole and a dual band F antenna were realized on 2 mm thick polypropylene substrate. Both antenna designs were also simulated using finite integration technique in the frequency domain (FI-FD). Measurements and full wave simulations of S11 of the antenna showed good agreement between measurements and simulations. Except for S11, the gain and radiation pattern of the antennas were measured and simulated. Maximum gain of the designed unipole antenna is around −10.0 and −5.5 dBi for 2.45 and 5.18 GHz frequency bands, respectively. The manufactured antennas are intended for application in wearable electronics, which can be used to monitor various activities such as walking, sleeping, heart rate or food consumption.