Rare earth elements (REE) are of strategic importance because they find numerous applications in various sectors of the global economy.The concern about the REE supply challenge has led to increasing interest and research in the recovery of REE from end-of-life products and secondary sources such as coal and coal by-products. The work reported here was focused on examining the technical feasibility of physical separation techniques for the enrichment of REE from coal and coal by-products. Particle size, magnetic and density separations were performed on coal, coal ash, clay and shale samples. It was found that the samples responded to particle size separation differently. For all ash samples, higher REE concentrations were found in the finer fractions. For the clay and shalesamples, however, the REE concentrations decrease as the particle size reduces possibly because RE minerals were not effectively released by grinding. Magnetic separation showed that REE are enriched in non-magnetic fractions for all ash samples. All samples responded similarly to density separation. Among the three methods, density separation showed the highest enrichment of REE. A combination of these methods is recommended. Finally, correlations between elements were demonstrated, which leads to the classification of three groups containing mainly Al/Si, Fe and Ca, respectively. REE are strongly associated with the Al/Si group.

No abstract

This work is part of our continuing efforts to address engineering issues related to the removal of tritiated water from off-gases produced in used nuclear fuel reprocessing facilities. In the current study, adsorption equilibrium of water on molecular sieve 3A beads was investigated. Adsorption isotherms for water on the UOP molecular sieve 3A were measured by a continuous-flow adsorption system at 298, 313, 333, and 353 K. Experimental data collected were analyzed by the Generalized Statistical Thermodynamic Adsorption (GSTA) isotherm model. The K + /Na + molar ratio of this particular type of molecular sieve 3A was ∼4:6. Our results showed that the GSTA isotherm model worked very well to describe the equilibrium behavior of water adsorption on molecular sieve 3A. The optimum number of parameters for the current experimental data was determined to be a set of four equilibrium parameters. This result suggests that the adsorbent crystals contain four energetically distinct adsorption sites. In addition, it was found that water adsorption on molecular sieve 3A follows a three-stage adsorption process. This three-stage adsorption process confirmed different water adsorption sites in molecular sieve crystals. The second adsorption stage is significantly affected by the K + /Na + molar ratio. In this stage, the equilibrium adsorption capacity at a given water vapor pressure increases as the K + /Na + molar ratio increases.

The objective of the current work was to shorten the gap for fundamental adsorption kinetic data required for the development of advanced adsorption unit-operation models to be incorporated into an overall plant-level model for spent nuclear fuel reprocessing. The kinetics of water-vapor adsorption on molecular sieve 3A was investigated at 25–80 °C and water dew points from −69 to 17 °C. Water uptake curves were fitted with three kinetic models including the linear-driving-force model, the shrinking-core model, and the Langmuir kinetic model. The results suggest that the water-vapor adsorption on molecular sieve 3A under the investigated experimental conditions was controlled by both external film resistance and internal macropore resistance. The contribution of the external film resistance varied from 25% to 50% of the total mass-transfer resistance depending on the adsorption temperature. It was also found that the Langmuir kinetic model fitted individual sets of kinetic data very well, but the Langmuir adsorption constant obtained from curve fitting decreased with increasing adsorption temperature and with increasing water vapor pressure. This result indicates a significant surface heterogeneity of molecular sieve 3A and also implicitly verifies that the Langmuir isotherm model is unable to represent isotherms of water adsorption on molecular sieve 3A.

Saline aquifers are the largest potential continental geologic CO2 sequestration resource. Understanding of potential geochemically induced changes to the porosity and permeability of host CO2 storage and sealing formation rock will improve our ability to predict CO2 plume dynamics, storage capacity, and long‐term reservoir behavior. Experiments exploring geochemical interactions of CO2/brine/rock on saline formations under CO2 sequestration conditions were conducted in a static system. Chemical interactions in core samples from the Lower Tuscaloosa formation from Jackson County, Mississippi, with exposure to CO2‐saturated brine under sequestration conditions were studied through six months of batch exposure. The experimental conditions to which the core samples of Lower Tuscaloosa sandstone and Selma chalk were exposed to a temperature of 85°C, CO2 pressure of 23.8 MPa (3500 psig), while immersed in a model brine representative of Tuscaloosa Basin. Computed tomography (CT), X‐Ray diffraction (XRD), Scanning Electron Microscopy (SEM), brine chemistry, and petrography analyses were performed before and after the exposure. Permeability measurements from the sandstone core sample before and after exposure showed a permeability reduction. No significant change of the permeability measurements was noticed for the core sample obtained from Selma chalk after it was exposed to CO2/brine for six months. These results have implications for performance of the storage interval, and the integrity of the seal in a CO2 storage setting. © 2016 Society of Chemical Industry and John Wiley & Sons, Ltd