For gas flows in microchannels, slip motion at the solid surface can occur even if the Mach number is negligibly small. Since the Knudsen number of the gas flow in a long microchannel can vary widely and the Navier-Stokes equations are not valid for Knudsen numbers beyond 0.1, an alternative method that can be applicable to continuum, slip and transition flow regimes is highly desirable. The lattice Boltzmann equation (LBE) approach has recently been expected to have such potential. However, some hurdles need to be overcome before it can be applied to simulate rarefied gas flows. The first major hurdle is to accurately model the gas molecule and wall surface interactions. In addition, the Knudsen number needs to be clearly defined in terms of LBE properties to ensure that the LBE simulation results can be checked against experimental measurements and other simulation results. In this paper, the Maxwellian scattering kernel is adopted to address the gas molecule and surface interactions with an accommodation coefficient (in addition to the Knudsen number) controlling the amount of slip motion. The Knudsen number is derived consistently with the macroscopic property based definition. The simulation results of the present LBE model are in quantitative agreement with the established theory in the slip flow regime. In the transition flow regime, the model captures the Knudsen minimum phenomenon qualitatively. Therefore, the LBE can be a competitive method for simulation of rarefied gas flows in microdevices
Passing one electric-current pulse through deformed pearlitic steel wires at room temperature causes the formation of cementite particles around 30 nm in size. This is found not only in some particular locations but throughout the cementite area, which reveals a different mechanism from traditional spheroidization of cementite plates because the latter leads to the formation of particles with much large size. Transmission electron microscopy images show electropulse-induced strain relief and formation of fine precipitations. Differential scanning calorimetry analysis demonstrates the additional stored free energy by electropulsing treatment. The raised free energy accounts the increased interface area in finer microstructure of materials. The experiment evidences that the passing electric current in metal has alternated the free energy sequence of various microstructures in comparison with that of current-free system.
We design and experimentally demonstrate a migration of electrically neutral particles in liquids driven by electric current according to the discrepancies of their electrical conductivities. A force from electric current to electrically neutral particles has been identified to drive the particles toward the lateral surface from the centre of suspension via three distinguishable zones, namely pushing, trapping and expelling zones. The driving force can overtake gravity in practical cases. The property of the force is found neither similar to that of the force in electromagnetophoresis nor similar to that of the electromigration force in terms of direction and magnitude. An expression for the force at the pushing zone has been developed based on the numerical calculation of the thermodynamics of suspension fluids.The excellent agreement between numerical calculations and experimental data demonstrates that our calculation provides fundamental and predictive insight into particles separation from the liquids. Therefore, it is possible to use the force in many engineering applications such as separation of particles according to the differences of their electrical conductivities. *Corresponding authors.
With appropriate electropulsing parameters, the microstructure of steels can be manipulated towards a state that possesses favourable physical, mechanical and chemical properties. This work demonstrates the application of designed electropulsing to pearlitic steel, transformation induced plasticity steel, austenite stainless steel and clean steel in order to generate novel microstructures that are difficult to achieve by other conventional thermomechanical processes. The principles for the design of electropulsing processing have been discussed. The method is particularly suitable for fabrication of the advanced multiphase and multicomponent alloys.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.