Transdermal patches of verapamil hydrochloride were prepared using four different polymers (individual and combination): Eudragit RL100 (ERL100), Eudragit RS100 (ERS100), hydroxypropyl methylcellulose 15 cps (HPMC), and ethyl cellulose (EC), of varying degrees of hydrophilicity and hydrophobicity. The effect of the polymers on the technological properties, i.e., drug release, water vapor transmission rate (WVTR), and percentage moisture loss (ML), percentage moisture absorption (MA), folding endurance, and thickness, was investigated. Different formulations were prepared in accordance with the 2(3) factorial design, with ERL100 being the parent polymer. The patch containing ERL100 alone showed maximum WVTR, % MA, and % ML, which could be attributed to its hydrophilic nature. As expected, substitution with ERS100, HPMC, and EC decreased all the above values in accordance with their decreasing degree of hydrophilicity. In vitro release studies showed zero-order release of the drug from all the patches, and the mechanism of release was diffusion mediated. Moreover, the release of the drug was sustained and it extended over a period of 24 hr in all formulations. A12 emerged as the most satisfactory formulation insofar as its technological properties were concerned. Further, release and permeation of the drug from the most satisfactory formulation (A12) was evaluated through different biological barriers (shed snake skin, rabbit skin, and rat skin) to get an idea of the drug permeation through human skin. Shed snake's skin was found to be most permeable (82.56% drug release at 24 hr) and rat skin was least permeable (52.38%). Percutaneous absorption studies were carried out in rabbits. The pharmacokinetic parameters calculated from blood levels of the drug revealed a profile typical of a sustained release formulation, with the ability to maintain adequate plasma levels for 24 hr. [AUC: 3.09 mg/mL hr, Cmax: 203.95 microg/mL, Tmax: 8 hr]. It can therefore be concluded that the patch containing ERL100 and HPMC in the ratio 8:2 has achieved the objectives of transdermal drug delivery system, such as avoidance of first pass effect, extended release, and reduced frequency of administration.

No abstract

The objective of the study is to formulate bilayer tablets consisting of atorvastatin calcium (AT) as an immediate release layer and nicotinic acid (NA) as an extended release layer. The immediate release layer was prepared using super disintegrant croscarmellose sodium and extended release layer using hydroxypropylmethyl cellulose (HPMC K100M). Both the matrix and bilayer tablets were evaluated for hardness, friability, weight variation, thickness, and drug content uniformity and subjected to in vitro drug release studies. The amount of AT and NA released at different time intervals were estimated by HPLC method. The bilayer tablets showed no significant change either in physical appearance, drug content or in dissolution pattern after storing at 40°C/75% relative humiding (RH) for 3 months. The release of the drug from the tablet was influenced by the polymer content and it was much evident from thermogravimetry/differential thermal analysis (TG/DTA) analysis. The results indicated that the bilayer tablets could be a potential dosage form for delivering AT and NA.

No abstract

UV Spectrophotometric method was developed and validated for the quantitative determination of Prothionamide in bulk drug and in pharmaceutical formulations. Prothionamide shows the maximum absorbance at 288 nm in phosphate buffer (pH 7.4). Prothionamide follows Beer’s law in the concentration range of 4-20 µg/ml (r2 = 0.999). The detection limit (DL) and quantitation limit (QL) were 0.406 and 1.229 µg/ml respectively. Accuracy and precision were found to be satisfactory. The developed methods were validated according to ICH guidelines. All the validation parameters were found to be satisfactory accordance with the standard values. Therefore, the proposed method can be used for routine practice for the determination of Prothionamide in assay of bulk drug and pharmaceutical formulations.International Current Pharmaceutical Journal, June 2015, 4(7): 402-404