No abstract

This paper presents the results of a study on developing an effective technique to increase the performance characteristics of antenna arrays for sub-THz integrated circuit applications. This is essential to compensate the limited power available from sub-THz sources. Although conventional array structures can provide a solution to enhance the radiation-gain performance however in the case of small-sized array structures the radiation properties can be adversely affected by mutual coupling that exists between the radiating elements. It is demonstrated here the effectiveness of using SIW technology to suppress surface wave propagations and near field mutual coupling effects. Prototype of 2 × 3 antenna arrays were designed and constructed on a polyimide dielectric substrate with thickness of 125 μm for operation across 0.19–0.20 THz. The dimensions of the array were 20 × 13.5 × 0.125 mm3. Metallization of the antenna was coated with 500 nm layer of Graphene. With the proposed technique the isolation between the radiating elements was improved on average by 22.5 dB compared to a reference array antenna with no SIW isolation. The performance of the array was enhanced by transforming the patch to exhibit metamaterial characteristics. This was achieved by embedding the patch antennas in the array with sub-wavelength slots. Compared to the reference array the metamaterial inspired structure exhibits improvement in isolation, radiation gain and efficiency on average by 28 dB, 6.3 dBi, and 34%, respectively. These results show the viability of proposed approach in developing antenna arrays for application in sub-THz integrated circuits.

In recent years, metal oxide‐based, inexpensive, stable electrodes are being explored as a potent source of high performance, sustainable supercapacitors. Here, the employment of industrial waste red mud as a pseudocapacitive electrode material is reported. Mechanical milling is used to produce uniform red mud nanoparticles, which are rich in hematite (Fe 2 O 3 ), and lower amounts of other metal oxides. A comprehensive supercapacitive study of the electrode is presented as a function of ball‐milling time up to 15 h. Ten‐hour ball‐milled samples exhibit the highest pseudocapacitive behavior with a specific capacitance value of ≈317 F g −1 , at a scan rate of 10 mV s −1 in 6 m aqueous potassium hydroxide electrolyte solution. The modified electrode shows an extraordinary retention of ≈97% after 5000 cycles. A detailed quantitative electrochemical analysis is carried out to understand the charge storage mechanism at the electrode–electrolyte interface. The formation of uniform nanoparticles and increased electrode stability are correlated with the high performance. This work presents two significant benefits for the environment; in energy storage, it shows the production of a stable and efficient supercapacitor electrode, and in waste management with new applications for the treatment of red mud.

No abstract

Laser-induced graphene (LIG) on paper substrates is a desirable material for single-use point-of-care sensing with its high-quality electrical properties, low fabrication cost, and ease of disposal. While a prior study has shown how the repeated lasing of substrates enables the synthesis of high-quality porous graphitic films, however, the process−property correlation of lasing process on the surface microstructure and electrochemical behavior, including charge-transfer kinetics, is missing. The current study presents a systematic in-depth study on LIG synthesis to elucidate the complex relationship between the surface microstructure and the resulting electroanalytical properties. The observed improvements were then applied to develop high-quality LIG-based electrochemical biosensors for uric acid detection. We show that the optimal paper LIG produced via a dual pass (defocused followed by focused lasing) produces high-quality graphene in terms of crystallinity, sp 2 content, and electrochemical surface area. The highest quality LIG electrodes achieved a high rate constant k 0 of 1.5 × 10 −2 cm s −1 and a significant reduction in chargetransfer resistance (818 Ω compared with 1320 Ω for a commercial glassy carbon electrode). By employing square wave anodic stripping voltammetry and chronoamperometry on a disposable two-electrode paper LIG-based device, the improved charge-transfer kinetics led to enhanced performance for sensing of uric acid with a sensitivity of 24.35 ± 1.55 μA μM −1 and a limit of detection of 41 nM. This study shows how high-quality, sensitive LIG electrodes can be integrated into electrochemical paper analytical devices.