This article presents the circularly polarized antenna operating over 28 GHz mm-wave applications. The suggested antenna has compact size, simple geometry, wideband, high gain, and offers circular polarization. Afterward, two-port MIMO antenna are designed to get Left Hand Circular Polarization (LHCP) and Right-Hand Circular Polarization (RHCP). Four different cases are adopted to construct two-port MIMO antenna of suggested antenna. In case 1, both of the elements are placed parallel to each other; in the second case, the element is parallel but the radiating patch of second antenna element are rotated by 180°. In the third case, the second antenna element is placed orthogonally to the first antenna element. In the final case, the antenna is parallel but placed in the opposite end of substrate material. The S-parameters, axial ratio bandwidth (ARBW) gain, and radiation efficiency are studied and compared in all these cases. The two MIMO systems of all cases are designed by using Roger RT/Duroid 6002 with thickness of 0.79 mm. The overall size of two-port MIMO antennas is 20.5 mm × 12 mm × 0.79 mm. The MIMO configuration of the suggested CP antenna offers wideband, low mutual coupling, wide ARBW, high gain, and high radiation efficiency. The hardware prototype of all cases is fabricated to verify the predicated results. Moreover, the comparison of suggested two-port MIMO antenna is also performed with already published work, which show the quality of suggested work in terms of various performance parameters over them.

In this paper, single-layer ultra-Wide Band (UWB) microstrip patch antennas loaded with asymmetrical U-shaped slot in both microwave and millimeter wave applications are presented. These novel antennas cover a fractional bandwidth around 40% in both microwave and millimeter applications. The applications cover the C-band (4-8) GHz, V-band (40-75) GHz, and W-band (75-110) GHz. In addition to that, it is the sole article that cover the bands (5.15-5.825) GHz and (8.025-8.4) GHZ for WiMaX and ITU band applications, respectively. Moreover, it covers three bands for Automotive radar applications within (71-76) GHz, (81-86) GHz, and (92-95) GHz, in addition to further 5G/mm-wave applications at 60 GHz. Each antenna is coaxial fed and implemented on a Roger 5880 substrate with relative dielectric constant of 2.2, thickness of 1.575 mm and loss tangent of 0.0009. They operate over the frequency band (5.5-9.5) GHz for microwave band and (55-95) GHz for mm-wave band. To achieve either a notch in other bands or develop a multi-band structure, the conventional ground is replaced by two different structures. The first ground is an array of patches and the other is a mushroom ground. The first ground results in a notch within the band (73-79) GHz while the second one achieves a multi-band within (55-68) GHz and (81-95) GHz. Both antennas are simulated and verified using Finite Difference Time-Domain analysis (FDTD); CST Microwave Studio and Finite Element Method (FEM); Ansoft HFSS. For microwave band, the antenna is fabricated and measured for verification. Concerning the mm-wave version, three different types of ground planes are presented; traditional, periodic structure of patches and mushroom. The structure with periodic patches conducts the same band as the traditional ground plane does. This is a prestep for the design of the notches. The mushroom ground is carried out for multi-band applications. The average gain of the antennas is 7 dB.The measured two dimensional cuts of the radiation pattern, radiation efficiency, and reflection coefficient of the microwave version are presented and are in good agreement with the simulated results while for the mm-wave antenna the same parameters are simulated with two different methods and are in good agreement.

In this article, a single-layer frequency selective surface (FSS)-loaded compact coplanar waveguide (CPW)-fed antenna is proposed for very high-gain and ultra-wideband applications. At the initial stage, a geometrically simple ultra-wideband (UWB) antenna is designed which contains CPW feed lines and a multi-stub-loaded hexagonal patch. The various stubs are inserted to improve the bandwidth of the radiator. The antenna operates at 5–17 GHz and offers 6.5 dBi peak gain. Subsequently, the proposed FSS structure is designed and loaded beneath the proposed UWB antenna to improve bandwidth and enhance gain. The antenna loaded with FSS operates at an ultra-wideband of 3–18 GHz and offers a peak gain of 10.5 dBi. The FSS layer contains 5 × 5 unit cells with a total dimension of 50 mm × 50 mm. The gap between the FSS layer and UWB antenna is 9 mm, which is fixed to obtain maximum gain. The proposed UWB antenna and its results are compared with the fabricated prototype to verify the results. Moreover, the performance parameters such as bandwidth, gain, operational frequency, and the number of FSS layers used in the proposed antenna are compared with existing literature to show the significance of the proposed work. Overall, the proposed antenna is easy to fabricate and has a low profile and simple geometry with a compact size while offering a very wide bandwidth and high gain. Due to all of its performance properties, the proposed antenna system is a strong candidate for upcoming wideband and high-gain applications.