Abstract:A relatively unknown natural fiber extracted from the leaves of the fique plant, native of the South American Andes, has recently shown potential as reinforcement of polymer composites for engineering applications. Preliminary investigations indicated a promising substitute for synthetic fibers, competing with other well-known natural fibers. The fabric made from fique fibers have not yet been investigated as possible composite reinforcement. Therefore, in the present work a more thorough characterization of fique fabric as a reinforcement of composites with a polyester matrix was performed. Thermal mechanical properties of fique fabric composites were determined by dynamic mechanical analysis (DMA). The ballistic performance of plain woven fique fabric-reinforced polyester matrix composites was investigated as a second layer in a multilayered armor system (MAS). The results revealed a sensible improvement in thermal dynamic mechanical behavior. Both viscoelastic stiffness and glass transition temperature were increased with the amount of incorporated fique fabric. In terms of ballistic results, the fique fabric composites present a performance similar to that of the much stronger Kevlar TM as an MAS second layer with the same thickness. A cost analysis indicated that armor vests with fique fabric composites as an MAS second layer would be 13 times less expensive than a similar creation made with Kevlar™.

No abstract

Natural cellulose-based fibers offer low cost, low density composite reinforcement with good strength and stiffness. Because of their annual renewability and biodegradability, natural fibers have materialized as environmentally-friendly alternatives to synthetic fibers in the last two decades. They are replacing synthetic materials in some traditional composites in industrial manufacturing sectors such as automotive, construction, furniture, and other consumer goods. In this work, the use of lignocellulosic fibers in green materials engineering, particularly their application as polymeric composite reinforcement and surface treatment via ionizing radiation are reviewed. Because these cellulose-based materials are intrinsically hydrophilic, they require surface modification to improve their affinity for hydrophobic polymeric matrices, which enhances the strength, durability, and service lifetime of the resulting lignocellulosic fiber-polymer composites. In spite of a long history of using chemical methods in the modification of material surfaces, including the surface of lignocellulosic fibers, recent research leans instead towards application of ionizing radiation. Ionizing radiation methods are considered superior to chemical methods, as they are viewed as clean, energy saving, and environmentally friendly. Recent applications of controlled ionizing radiation doses in the formulation of natural fiber -reinforced polymeric composites resulted in products with enhanced fiberpolymer interfacial bonding without affecting the inner structure of lignocellulosic fibers. These applications are critically reviewed in this contribution.

A typical multilayered armor system (MAS) is composed of a harder front ceramic tile, which is able to erode heavy ammunition, such as the 7.62 mm bullet, followed by a second layer to further reduce the impact energy. Aramid fabric is a common choice for the second layer. In the present work, polyester matrix composites reinforced with 10 to 30 vol% of curaua fibers, despite having much lower strength and stiffness than aramid fabric, displayed similar trauma indentation in a standard clay witness simulating the human body. Impedance matching and scanning electron microscopy analyses suggest effective energy absorption through ceramic fragment capture by curaua composites. Additionally, because of the high cost of aramid fabric, a full MAS with curaua fiber composite is much cheaper than a MAS composed of aramid fabric. Taking into consideration, both the economical and environmental advantages of natural fibers, it is concluded that curaua fiber-reinforced polyester composite could replace aramid fabric as the second layer in MASs for personal ballistic protection. POLYM. ENG. SCI., 57:947-954,

Natural-fiber-reinforced polymer composites have recently drawn attention as new materials for ballistic armor due to sustainability benefits and lower cost as compared to conventional synthetic fibers, such as aramid and ultra-high-molecular-weight polyethylene (UHMWPE). In the present work, a comparison was carried out between the ballistic performance of UHMWPE composite, commercially known as Dyneema, and epoxy composite reinforced with 30 vol % natural fibers extracted from pineapple leaves (PALF) in a hard armor system. This hard armor system aims to provide additional protection to conventional level IIIA ballistic armor vests, made with Kevlar, by introducing the PALF composite plate, effectively changing the ballistic armor into level III. This level of protection allows the ballistic armor to be safely subjected to higher impact projectiles, such as 7.62 mm caliber rifle ammunition. The results indicate that a hard armor with a ceramic front followed by the PALF/epoxy composite meets the National Institute of Justice (NIJ) international standard for level III protection and performs comparably to that of the Dyneema plate, commonly used in armor vests.