Polymer‐based photovoltaic cells, with periodic sub‐micrometer structures as an efficient light‐trapping scheme, are investigated to improve the performance of organic solar cells based on poly(3‐hexylthiophene) and 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl‐(6,6)C61. A soft lithographic approach that uses photoresponsive azo polymer films as masters and poly(dimethylsiloxane) as stamps is used to form surface relief gratings (SRGs) on the active layers. The effect of periodic gratings on solar cell performance is precisely investigated according to various grating conditions such as period, depth, and dimension. The solar cells with 1D and 2D SRGs present improved incident‐photon‐to‐current conversion efficiencies and an overall increase in power conversion efficiencies, primarily resulting from the enhancement of short‐circuit current density, indicating that periodic structures induce further photon absorption in the active film.

Novel poly[(9,9‐bis((6′‐(N,N,N‐trimethylammonium)hexyl)‐2,7‐fluorene)‐alt‐(9,9‐bis(2‐(2‐(2‐methoxyethoxy)ethoxy)ethyl)‐9‐fluorene)) dibromide (WPF‐6‐oxy‐F) and poly[(9,9‐bis((6′‐(N,N,N‐trimethylammonium)hexyl)‐2,7‐fluorene)‐alt‐(9,9‐bis(2‐(2‐methoxyethoxy)ethyl)‐fluorene)] dibromide (WPF‐oxy‐F) compounds are developed and the use of these water‐soluble polymers as an interfacial layer for low‐cost poly(3‐hexylthiophene):phenyl‐C61 butyric acid methyl ester (P3HT:PCBM) organic solar cells (OSCs) is investigated. When WPF‐oxy‐F or WPF‐6‐oxy‐F is simply inserted between the active layer and the cathode as an interfacial dipole layer by spin‐coating water‐soluble polyfluorenes, the open‐circuit voltage (Voc), fill factor (FF), and power‐conversion efficiency (PCE) of photovoltaic cells with high work‐function metal cathodes, such as Al, Ag, Au, and Cu, dramatically increases. For example, when WPF‐6‐oxy‐F is used with Al, Ag, Au, or Cu, regardless of the work‐function of the metal cathode, the Voc is 0.64, 0.64, 0.58, and 0.63 V, respectively, approaching the original value of the P3HT:PCBM system because of the formation of large interfacial dipoles through a reduction of the metal work‐function. In particular, introducing WPF‐6‐oxy‐F into a low‐cost Cu cathode dramatically enhanced the device efficiency from 0.8% to 3.36%.

Colloidal-quantum-dot (CQD) photovoltaic devices are promising candidates for low-cost power sources owing to their low-temperature solution processability and bandgap tunability. A power conversion efficiency (PCE) of >10% is achieved for these devices; however, there are several remaining obstacles to their commercialization, including their high energy loss due to surface trap states and the complexity of the multiple-step CQD-layer-deposition process. Herein, high-efficiency photovoltaic devices prepared with CQD-ink using a phase-transfer-exchange (PTE) method are reported. Using CQD-ink, the fabrication of active layers by single-step coating and the suppression of surface trap states are achieved simultaneously. The CQD-ink photovoltaic devices achieve much higher PCEs (10.15% with a certified PCE of 9.61%) than the control devices (7.85%) owing to improved charge drift and diffusion. Notably, the CQD-ink devices show much lower energy loss than other reported high-efficiency CQD devices. This result reveals that the PTE method is an effective strategy for controlling trap states in CQDs.

The authors report on a spray deposition method as a cost-efficient technique for the fabrication of organic solar cells (OSCs). Active layers of OSCs were fabricated using conventional handheld airbrushes. Although the spray deposited film showed a relatively rougher surface than spin coated ones, pinhole-free and constant thickness films could be obtained. An optimized OSC showed 2.83% of power conversion efficiency and 52% of incident photon to current conversion efficiency even though the device was fabricated in air. The performance of sprayed OSCs was comparable to that of the spin coated devices fabricated in air.

High-efficiency colloidal quantum dot photovoltaic devices (CQDPVs) are achieved by improving the interfacial charge extraction via chemical modification of PbS-CQD/ZnO heterojunctions. Simple treatment of the heterojunctions using a chemical modifier, 1,2-ethanedithiol, effectively reduces the interband trap sites of the ZnO nanoparticles (ZnO-np) by passivation of the notorious intrinsic oxygen-deficient defects. As a result, the interfacial bimolecular recombinations between (i) trapped electrons in the ZnO-np layers and the holes in the CQD layers and (ii) accumulated electrons in the CQD layers and the holes in the CQD layers are suppressed. Consequently, the power conversion efficiency of the chemically modified CQDPVs reached a certified power conversion efficiency of 10.14% with decent air stability. Notably, the entire device fabrication process, including chemical modification, could be performed at room temperature under ambient atmosphere.