Fully printed perovskite solar cells are demonstrated with slot-die coating, a scalable printing method. A sequential slot-die coating process is developed to produce efficient perovskite solar cells and to be used in a large-scale roll-to-roll printing process. All layers excluding the electrodes are printed and devices demonstrate up to 11.96% power conversion efficiency. It is also demonstrated that the new process can be used in roll-to-roll production.

No abstract

Here, an investigation of three‐dimensional (3D) morphologies for bulk heterojunction (BHJ) films based on regioregular poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) is reported. Based on the results, it is demonstrated that optimized post‐treatment, such as solvent annealing, forces the PCBM molecules to migrate or diffuse toward the top surface of the BHJ composite films, which induces a new vertical component distribution favorable for enhancing the internal quantum efficiency (ηIQE ) of the devices. To investigate the 3D BHJ morphology, novel time‐of‐flight secondary‐ion mass spectroscopy studies are employed along with conventional methods, such as UV‐vis absorption, X‐ray diffraction, and high‐resolution transmission electron microscopy studies. The ηIQE of the devices are also compared after solvent annealing for different times, which clearly shows the effect of the vertical component distribution on the performance of BHJ polymer solar cells. In addition, the fabrication of high‐performance P3HT:PCBM solar cells using the optimized solvent‐annealing method is reported, and these cells show a mean power‐conversion efficiency of 4.12% under AM 1.5G illumination conditions at an intensity of 100 mW cm−2.

Hybrid perovskites are recently developed photoactive semiconductors that hold great promise for next-generation solar cells, with devices incorporating them reaching certified efficiencies as high as 22.1%. [1] This high performance is coupled with a relative low cost, as perovskites comprise earth-abundant elements that are amenable to deposition from the solution-state by scalable, inexpensive printing processes. [2] Recent work has focused on improving their long-term stability with significant progress being reported in encapsulation techniques and scalability with the production of modulescale devices (100 cm 2 ) exhibiting efficiencies of over 11%. [3][4][5][6] These developments have resulted in efforts to commercialize perovskite solar cells; however, there is still concern over the potential to achieve the 25-year service lifetimes necessary to make perovskites a disruptive technology.Photoactive perovskite semiconductors are highly tunable, with numerous inorganic and organic cations readily incorporated to modify optoelectronic properties. However, despite the importance of device reliability and long service lifetimes, the effects of various cations on the mechanical properties of perovskites are largely overlooked. In this study, the cohesion energy of perovskites containing various cation combinations of methylammonium, formamidinium, cesium, butylammonium, and 5-aminovaleric acid is reported. A trade-off is observed between the mechanical integrity and the efficiency of perovskite devices. High efficiency devices exhibit decreased cohesion, which is attributed to reduced grain sizes with the inclusion of additional cations and PbI 2 additives. Microindentation hardness testing is performed to estimate the fracture toughness of single-crystal perovskite, and the results indicated perovskites are inherently fragile, even in the absence of grain boundaries and defects. The devices found to have the highest fracture energies are perovskites infiltrated into a porous TiO 2 /ZrO 2 /C triple layer, which provide extrinsic reinforcement and shielding for enhanced mechanical and chemical stability. Perovskite Solar CellsThe ORCID identification number(s) for the author(s) of this article can be found under https://doi.

Novel poly[(9,9‐bis((6′‐(N,N,N‐trimethylammonium)hexyl)‐2,7‐fluorene)‐alt‐(9,9‐bis(2‐(2‐(2‐methoxyethoxy)ethoxy)ethyl)‐9‐fluorene)) dibromide (WPF‐6‐oxy‐F) and poly[(9,9‐bis((6′‐(N,N,N‐trimethylammonium)hexyl)‐2,7‐fluorene)‐alt‐(9,9‐bis(2‐(2‐methoxyethoxy)ethyl)‐fluorene)] dibromide (WPF‐oxy‐F) compounds are developed and the use of these water‐soluble polymers as an interfacial layer for low‐cost poly(3‐hexylthiophene):phenyl‐C61 butyric acid methyl ester (P3HT:PCBM) organic solar cells (OSCs) is investigated. When WPF‐oxy‐F or WPF‐6‐oxy‐F is simply inserted between the active layer and the cathode as an interfacial dipole layer by spin‐coating water‐soluble polyfluorenes, the open‐circuit voltage (Voc), fill factor (FF), and power‐conversion efficiency (PCE) of photovoltaic cells with high work‐function metal cathodes, such as Al, Ag, Au, and Cu, dramatically increases. For example, when WPF‐6‐oxy‐F is used with Al, Ag, Au, or Cu, regardless of the work‐function of the metal cathode, the Voc is 0.64, 0.64, 0.58, and 0.63 V, respectively, approaching the original value of the P3HT:PCBM system because of the formation of large interfacial dipoles through a reduction of the metal work‐function. In particular, introducing WPF‐6‐oxy‐F into a low‐cost Cu cathode dramatically enhanced the device efficiency from 0.8% to 3.36%.